- ページ 4

室内装飾品 Cube UP 6000 SeriesのPDF 組立マニュアルをオンラインで閲覧またはダウンロードできます。Cube UP 6000 Series 4 ページ。

ページを印刷する

User manual

Preface

Congratulations on your new Cube Design UP sit-stand desk. The desk is an

electrically driven desk, intended for indoor use in office environments. The

desk is also suitable for home offices. Carefully read this manual before using

the desk. The instruction manual must always follow the sit-stand desk.

Table information

The height adjustment of the sit-stand desk is driven by Jiecang, where

each column is equipped with an engine. These are controlled from a

control box which is connected to the control panel. The control box must

be plugged into 230 volt power outlet and has built-in electronic overload

protection that can not be replaced. The sit-stand desk is double insulated

and does not need grounding.

Important information

A sit-stand desk must always be reset after assembly. This adjustment

is performed to ensure that the built-in motors work synchronously. It is

recommended that the procedure must take place when the UP desk asks

to be reset and every time the sit-stand desk is moved. Please follow the

procedure described here:

1. Connect the power

2. Press and hold the "down" button on the handset. Continue pressing until

the desk has reached the lowest position.

3. Press the "down" button in 5 seconds until the desk enters the reset state,

and the handset is going down to complete the reset.

Now the system is operational.

4. In normal state, the indicator light is off. In the error state, the indicator

light is on. In the reset state, the indicator light flashed.

Prohibitions, warnings and advice

• The sit-stand desk must not be used for lifting persons (eg. when replacing

light bulbs in ceiling lamps)

• The sit-stand desk must be leveled. If the ground is not level use the

adjustable shoes under the feet

• The sit-stand desk is intended to be activated continuously max. 2 min

at a time or a maximum of 6 minutes per. hour at full load

• Be aware of the risk of entrapment in the height of the table movement

• Pay special attention to children when they are near the sit-stand desk

• The entire table top must be free (minimum 25 mm) of shelving, frames,

tables and other similar objects

• The power cord must not be damaged or trapped

• Ensure that the wires for the computer, phone and network, etc. are long

enough. Gently run the sit-stand desk to the highest and lowest position

• The power must be switched off at the power outlet (eg. at night) if the

power consumption must be reduced to the maximum

Operating

The sit-stand desk can only be operated from the control panel mounted

under the table top. The panel has two buttons respectively up and down.

Arrow buttons show the direction. The table will move as long as one of the

buttons is pressed.

It is possible to reset the sit-stand desk by using this control panel (see section 3).

Be aware of crushing danger when using the height adjustment. The table

has no separate power switch - use the power outlet when the sit-stand desk

must be disconnected. If there is a malfunction or similar, see the Error table.

Maintenance

The moving mechanism must not be lubricated with oil or otherwise. Main-

tenance is limited to wiping the table top and frame with cloth dampened

in a mild soap. Stubborn stains may be removed with rubbing alcohol. Do

not allow water into the electrical parts.

Assembly of the table

The parts of the sit-stand desk are removed from all packaging. Make sure

that all parts, shown on the drawing, are represented. If parts are missing

please contact Cube Design.

Setup

The sit-stand desk should be placed on a flat surface and the table top adjusted

level with the adjustable shoes under the feet. It is necessary to reset the table

after adjusting the shoes (see section 3). All cables for the sit-stand desk must

be arranged and assembled, eg. in a flexible cabling, so that the cables do not

disturb the user and the function of the sit-stand desk.

Moving

The sit-stand desk should be run in the lowest position before moving it and

all conduit should be removed. Installation procedure is repeated for the

establishment of the new space.

10.

Repair

Repair of the sit-stand desk must be made by authorized repairer / technician,

because the sit-stand desk does not contain serviceable parts which the user

can repair.

11.

Warranty

Cube Design's warranty covers manufacturing and material defects discovered

during normal use of the sit-stand desk. The warranty does not cover defects

or damages directly or indirectly caused by misuse, violence or interference

by other than an authorized repairer / technician.

12.

Disposal

The sit-stand desk must be disposed as follows:

• Table top to incineration

• Metal structure for metal recycling

• Electronics for reception facilities for electronics

13.

Technical specifications

Dimensions

Following the table top, but a maximum of 200 cm x 110 cm

Electrical con.

230 V, 50 Hz, dobbelt insulated, no need for grounding

Power input

200 W

Standby

0,1 W

Sound level

maximum 50 dB(A)

Load

A maximum of 125 kg located centrally on the table

Operating temp. 0 degrees C to +40 degrees C

Air humidity

10 - 80 % RH (Relative Humidity)

Height variation 59,5-124,5 cm

Speed up/down A maximum of 40 mm./sec.

Continuous operation - Max. 2 min. continuously at full load or 6 min. per. hour (10%)

14.

Error

The sit-stand desk does not respond:

• Check connection to power input. Is it turned on?

• Check, that the wirring from the control box is connected

• Check, that the wire from the control device is connected

• Check, that the connectors are completely mounted in

• Check, that no wires have been cut / disconnected

• Check, that the mains fuses are OK

• If the sit-stand desk still does not respond please contact the supplier for service

The sit-stand desk does not run smoothly:

• Switch off at the power input and unplug

• Try to restart and initialize the sit-stand desk

• If the error still occurs please contact the supplier for service

The sit-stand desk is no longer level:

• Check adjustable shoes. If OK, run the sit-stand desk in the bottom of the

new initialization

The sit-stand desk makes an unusual noise:

• Check that the sit-stand desk is not rubbing against other sit-stand desks

or elements

• Locate the noise and if it is coming from the desk column, contact supplier

for service - Do not use the height adjustment until the service is completed

15.

Contact information

Cube Design A/S

Vadstedvej 212

DK-8450 Hammel

Phone no.

+45 86 98 74 11

Mail

[email protected]

Web