- ページ 6
キーパッド CAMDEN CM-120TXのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。CAMDEN CM-120TX 8 ページ。 Wireless digital keypads
ページを印刷するFirst, enter program mode. Then enter [*6], then 3#,
then 0 to disable, or 1 to enable, then *.
For example, [*6] 3 # 0 * will disable the audio tone on
incorrect code entry.
Request to Exit Audio Enable/
Disable - Function 5#
Default: 0 (Disabled)
Enable or disable audio annunciation for Channel #1
when a Request to Exit signal is input. When enabled,
if Channel 1 is triggered by REX input, a looped tone
(do-ray) will be annunciated for the duration that Relay
#1 is energized. In the case of Toggled mode, the
annunciation will last for 8 seconds (hard-coded). In the
case of entering into Unlocked Mode (REX input held
for more than 15 seconds), 4 beeps will sound after the
looped two-tone annunciation. A single ("Ray-Do") tone
will sound when exiting Unlock Mode.
0 = disabled
1 = enabled
To enable/disable REX Audio Annunciation:
First, enter program mode. Then enter [*6], then 5#,
then 0 to disable, or 1 to enable, then *.
For example, [*6] 5 # 1 * will enable the audio
annunciation for REX input.
FACTORY DEFAULT SETTINGS
If the settings have not been changed after shipment,
or if they have been reset, they are as follows:
o Master User # 1 - Code is 1234.
o Main Channel = 3 sec
o Secondary Channel = programmable.
o Yellow LED enabled.
Reset to Factory Defaults
Reset the Master Code:
While holding the # and * down together for
aprox. 4 secs, power up the keypad. There will
be 4 beeps and all LED's will flash. The keypad
will immediately move into the battery life
indicator. It will beep up to 5 times and the green
LED will flash.
Reset the keypad to factory defaults:
While holding down the # and * for approx. 10
seconds. Power up the keypad. There will be the
initial 4 beeps at the 4 second point, indicating the
Master Code is reset
battery test beeps (up to 5), then followed by 8
beeps indicating the keypad has been reset to
factory defaults.
[*9] Erase Keypad Memory/Reset ALL to
Factory
Force factory default settings (use with caution)
This is used when most or all of the programming has
to be changed, as when a keypad has been moved to a
new location. To reset to factory defaults.
First, enter program mode. Then enter [*9], then re-
enter the master keycode, then *.
For example, [*9] 1 2 3 4 * will immediately and
permanently clear the entire memory (assuming the
master keycode has not been changed from the factory
default. Once this function has been executed, there is
NO WAY to restore the previous
Section 4 _________________
Technical Data
Model
Illumination
Size
Mounting
Temperature
Operating voltage
Battery Life
Capacity
Length
Response time
Inputs
Output
6
Installation Instructions
(1234), followed by the
state.
CM-120TX
No
/ Yes
2 ¾" x 4 ½" x ¾"
69.85mm x 114.30mm x
19.05mm
2 x #6-32 machine security
screws
-40° - +185°F (-40° - +85°C)
2 x AA Alkaline Batteries
90,000 Operations
Based on a 4 digit user code
999 User codes
Up to 8 digits (10 million
possible codes)
0.3 seconds
1 x REX input
1 x Door Contact input
RF Only, 2 Channels
Channel 1 assigned to users
1 - 499
Channel 2 assigned to users
500 - 999