- ページ 2
サーバー ClearCube CD7424SFPSTのPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。ClearCube CD7424SFPST 3 ページ。 Zero client
ページを印刷するSmart Card Reader Setup
Prevent ESD (electrostatic discharge) damage to smart
card readers by always discharging your body and
smart card before using a reader (for example, by
touching a grounded, unpainted, metal object). ESD
can vary depending on many environmental conditions,
including clothing that users wear and how they handle smart
cards. ESD damage can potentially cause unsupported card reader
behavior including failure. Always perform ESD prevention steps
before using the card reader.
Driver Requirement
To use the smart card reader, install a reader driver on the remote
device to which you connect and ensure that the card reader
service is running on the remote device. Download the driver to
install on devices from the CD7424SFPST Drivers section of
ClearCube Support site at www.clearcube.com/support. The file
contains drivers for all supported operating systems and
installation instructions.
Pre-Session Authentication Firmware Requirement
TERA firmware revision 3.5.1 (or above) is required to support
pre-session authentication in your environment.
Buttons and Indicators
The list below shows indicators on the front panel and button operations:
• Power Button Colors
– Green (solid): CD7424SFPST is powered on.
– Green (blinking): PCoIP session is sleeping. Press any key
on the keyboard to wake the session.
– Orange: CD7424SFPST is powered off.
• Power Button Operations
– Power on: when orange, press briefly (button turns green)
– Disconnect session: when green, briefly press (button
blinks green)
– Power off: press and hold for 3 seconds (button turns orange)
• PCoIP Session Indicator—shows when a connection, or
session, is established between the CD7424SFPST and a blade.
The link indicator displays one of the following:
– Green—a session is established between the client and a blade.
– Off—there is no session between the client and a blade.
• Remote PC Power—when an CD7424SFPST is connected to
a remote PC host, you can press the Remote PC button on the
ClearCube Technology
8834 Capital of Texas Hwy N
Austin, Texas 78759
front of the CD7424SFPST to put the remote PC in a soft off
(S5, hot) power state. Press the button again to wake the remote
PC. Video resumes at the OS login screen. You can change the
action performed when users press the Remote PC power
button. See the PCoIP User's Guide for more information.
• Smart Card Reader
– Yellow-Green—smart card reader is powered on.
– Red—smart card has been reset. When red light is flashing,
the IC Card is reading or writing.
• Connection Status Indicators
LED
State
Steady
Power on
PWR
Off
No power
Steady
TX port: network connection made (copper)
LNKC
Off
No connection
Steady
RX port: network connection made (fiber)
LNKF
Off
No connection
FDX/COL Steady
Full duplex connection
Steady
Receiving data
RX
Off
No reception
Steady
Transmitting data
TX
Off
No transmission
Mandatory Setup & Cooling Requirements
• Ensure at least 4 inches of space around all zero client edges
and at least 2 inches of space above the client.
• Ambient temperature around a client must not exceed 35° C (95° F).
• Do not stack any objects on top of the zero client.
• Do not block the zero client's side vents by leaning papers,
folders, computer speakers, or any other objects against the
sides of the client.
• Adjacent furniture (file drawers, desk supports, chairs) do not
block or enclose any sides of the zero client.
• Ensure that the zero client is standing vertically.
• Do not place the zero client in enclosed environments such as
on a shelf or inside a drawer.
• Ensure that cables connected to the zero client are supported.
Setting up the CD7424SFPST Zero Client
Perform the following steps to connect peripherals and a network
cable to the zero client.
ENSURE YOU FOLLOW THE
MOUNTING & COOLING REQUIREMENTS DETAILED BELOW.
FAILURE TO DO SO CAN DAMAGE THE ZERO CLIENT.
voice 512 652 3500 www.clearcube.com
Meaning
—Continued—
G0200150 Rev A