- ページ 16

コントローラー dixell CoolMate XLR130CのPDF 設置および操作方法をオンラインで閲覧またはダウンロードできます。dixell CoolMate XLR130C 20 ページ。 Cool mate

12.2 HOW TO PROGRAM AN INSTRUMENT USING A HOT KEY (DOWNLOAD)

Turn OFF the instrument.

Insert a programmed "Hot Key" into the 5 PIN receptacle and then turn the Controller ON.

Automatically the parameter list of the "Hot Key" is downloaded into the Controller memory, the "doL" message is blinking followed a by

flashing "End".

After 10 seconds the instrument will restart working with the new parameters.

Remove the "Hot Key"..

NOTE the message "Err" is displayed for failed programming. In this case turn the unit off and then on if you want to restart the download again or

remove the "Hot key" to abort the operation.

13. ALARM SIGNALS

Message Cause

"P1"

Thermostat probe failure

"P2"

Evaporator probe failure

"P3"

Auxiliary probe failure

"HA"

Max. temperature alarm

"LA"

Min. temperature alarm

"EE"

Data or memory failure

"dA"

Door switch alarm

"EAL"

External alarm

"BAL"

Serious external alarm

"PAL"

Pressure switch alarm

PAn

"Panic" Alarm

"rtc"

Real time clock alarm

The alarm message is displayed until the alarm condition is recovery.

All the alarm messages are showed alternating with the room temperature except for the "P1" which is flashing.

To reset the "EE" alarm and restart the normal functioning press any key, the "rSt" message is displayed for about 3s.

13.1 SILENCING BUZZER / ALARM RELAY OUTPUT

If "tbA = y", once the alarm signal is detected the buzzer and the relay are is silenced by pressing any key.

If "tbA = n", only the buzzer is silenced while the alarm relay is on until the alarm condition recovers.

13.2 "EE" ALARM

The dIXEL instruments are provided with an internal check for the data integrity. Alarm "EE" flashes when a failure in the memory data occurs. In

such cases the alarm output is enabled.

13.3 ALARM RECOVERY

Probe alarms : "P1" (probe1 faulty), "P2" and "P3"; they automatically stop 10s after the probe restarts normal operation. Check connections before

replacing the probe.

Temperature alarms "HA" and "LA" automatically stop as soon as the thermostat temperature returns to normal values or when the defrost starts.

Door switch alarm "dA" stop as soon as the door is closed.

External alarms "EAL", "BAL" stop as soon as the external digital input is disabled "PAL" alarm is recovered by switching OFF the instrument.

14. TECHNICAL DATA

Housing: self extinguishing ABS; Case: frontal 210x230 mm; depth 87mm; Mounting: See par. 9; Protection: IP65

Connections: Screw terminal block ≤ 2,5 mm

Power supply: 230Vac 50/60Hz

Display:3 digits, red LED, 30.5 mm high.

Inputs: 3 NTC or PTC probes

Digital inputs : doorswitch and configurable, free voltage. Max. distance 10m

Relay outputs:

compressor: relay SPST 20(8) A, 250Vac

light: relay SPST 16(3) A, 250Vac

fans: relay SPST 8(3) A, 250Vac

defrost: relay SPDT 16(3) A, 250Vac

alarm: SPDT relay 8(3) A, 250Vac

auxiliary: SPST relay 20(8) A, 250Vac

Other output :

Alarm buzzer (Standard)

Direct RS485 (optional)

1592017000 XLR 130-170 GB r2.0 23.03.2015

Outputs

Alarm output ON; Compressor output according to parameters "COn" and "COF"

Alarm output ON; Other outputs unchanged

Alarm output ON;

Other outputs unchanged

Alarm output ON; Other outputs unchanged

Alarm output ON; Other outputs OFF

Alarm output ON; Other outputs unchanged

Alarm output ON; Other outputs unchanged; Defrosts according to par. "IdF"

wiring.

10%; Power absorption: 10VA max.

10% or 110Vac 50/60Hz

XL130 - XLR170

16/20