- ページ 5

インバーター AIMS AIMS Power PE300012230SのPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。AIMS AIMS Power PE300012230S 6 ページ。 Dc to ac pure sine wave inverter

ページを印刷する

6) The cooling fans inside the inverter do not work until the case temperature rises up to

about 104°For40°C.

7) Switch off inverter or remote to turn off. At that time, the indicator lights for both inverter

and remote are off. The inverter does not consume current from the battery when it is

switched off.

② How to use USB power supply

This model supplies a USB output, and provides stable voltage at 5V DC, maximum

current 2.1A directly to a portable device with USB port.

Notice: Before using the USB power supply, please make sure the device can be charged

by USB and the maximum working current is no more than 2.1A.

8. About soft start technology

The output voltage rises up from low to normal when the inverter is turned on. This can

reduce high startup currents, which can make startup easier for large inductive loads.

As for the large inductive loads, such as electric tools and capacitive loads, we suggest

turning on the switch of the appliance firstly and then the inverter's. The soft start may be

enough to power the high startup.

9. The output wave form

The output wave form of this inverter is a Pure Sine Wave, which is similar to utility-

supplied AC electricity. Pure sine wave is applicable in most loads, including electrical

equipment, such as Linear Adaptor, switching power supply, transformer, motor and so on.

Compared to Modified wave form, for inductive loads such as a refrigerator and electric

fans, pure sine wave form can improve its power factor and the battery's efficiency and

reduce working noises. For capacitive loads such as adapter of lap-top, pure sine wave

can lower the rush current at work and reduce interferences to increase reliability and

prolong the life of the product.

Pure Sine Wave Output

(230 VAC Model)

10. Protection

Features

1). Input under-voltage alarm: When the input DC voltage is lower than 9.8V for 12V

model and 21.2V for 24V model, the buzzer will whistle intermittently to remind that the

inverter will go into the under voltage protection. Pay attention to save the data if you are

using a computer.

312 Volta peak

2). Under voltage protection: The inverter will automatically shut down when the input

DC voltage is lower than 9.5V for 12V model and 20V for 24V model. The buzzer will

whistle continuously and the green light is off, red light is on. Please turn off the inverter

and use it after recharging the battery.

3). Over voltage protection: The inverter will automatically shut down when the input DC

voltage is higher than 16V for 12V model and 32V for 24V model. The buzzer will whistle

continuously and the green light is off, red light is on. Please turn off the inverter and

adjust the input voltage to the admissible range.

4). Overload protection: The inverter will automatically shut down when the load is

higher than the rated power. The buzzer will whistle continuously. Turn off the inverter and

resume normal operation after taking away the excessive load.

5). Short-circuit protection: The AC output will be automatically shut down when short

circuited. It will automatically reset after the problem is solved.

6). Thermal protection: The unit will get hot during operation. If the temperature is higher

than 149°F or 65°C, the inverter will automatically shut down. Then the buzzer will whistle

continuously and the green light is off, red light is on. Please turn off the inverter, and

continue using it after the temperature goes back to normal naturally. Meanwhile find out

the factors causing the fault, such as ventilation, ambient temperature, vent, load power

and so on. It can avoid similar things from happening again.

Notice:

In the case of over voltage, under voltage and thermal protection, the inverter will shut

down automatically after 1 minute if the user doesn't turn it off . When it is in the OFF

position, the inverter doesn't consume battery current.