- ページ 11
超音波ジュエリークリーナー Edic CR2 2700RCのPDF オーナーズ／オペレーターズ・マニュアルをオンラインで閲覧またはダウンロードできます。Edic CR2 2700RC 19 ページ。 17 gallon professional restroom cleaner
ページを印刷する
1. Power switch- Lights up when switched to power
"ON"
2. "INLET" hose connect to male Q.D. (#16 on page 4)
3. Lamp will turn on anytime the heat element is
activated. Lamp will turn off any time max temp is
reached.
4. Male twist lock Pigtail- connects to 50 ft cord
5. "OUTLET" male Q.D.- Connect to your 35ft solution
line
6. Handle
How to prepare an accessory heater for carpet
cleaning or upholstery:
1. Mount the Heater by lining up the two "legs" to the
two mounting brackets on the rear of the machine.
(#18 on page 7).
2. Connect your heater's "INLET" hose (#2 on page 10)
to #16 on page 7.
3. Connect your 35 ft solution hose (#3 on page 8) to
the heater's "OUTLET" Q.D. (#5 on page 10).
4. Connect your wand or upholstery tool to your 35ft
solution hose and 35ft Vacuum hose.
5. Connect the power cord for the machine and the
power cord for the heater into two separate plugs on
two separate circuits. You may use a 988CS circuit
locater if available to locate two separate circuits.
6. Fill the solution tank of your CR2 with water.
7. Place the pump switch into the "ON" position.
8. Make sure Chemical Dispensing Valve is in the
"RINSE" position.
9. If necessary, allow pump to prime for 10-30 seconds
by turning the priming/pressure relief valve (#15 on
page 4) 45 degrees to the left to the "O" open posi-
tion.
10. Allow pump to prime
11. Close the priming valve.
12. Turn pump on and spray out of your wand or uphol-
stery tool until you have an uninterrupted stream.
13. Turn heater on and allow up to 3 minutes for the unit
to heat up.
14. The heater is ready for use once the green lamp (#3
on page 6) shuts off the first time. Once you start
cleaning carpet, the green lamp will turn on and off
throughout your job as the thermostats regulate the
temperature.
15. Prespray as necessary.
16. Turn on the vacuum motor.
17. Spray on the backstroke and do a dry stroke when
pushing forward.
18. Overlap your previous path slightly when you pull
back.
19. Monitor the levels in the recovery tank and empty
as necessary. Use defoamer to ensure your vacuum
motor does not take in fluid
DO NOT ALLOW HEATER TO BE RUN DRY.
DO NOT ALLOW HEATER TO FREEZE.
Cleaning carpet or upholstery without a
heater:
The CR2 can be used as a cold water extractor.
If you do not have an accessory heater, then perform the
steps below.
1. Prespray the area of carpet to be cleaned
2. Connect your solution line
3. Connect your recovery vacuum hose
4. Connect your wand or upholstery tool to the solu-
tion and vacuum hoses
5. Fill the solution tank of your CR2 with water
6. Make sure Chemical Dispensing Valve is in the
"RINSE" position
7. Place the pump switch into the "ON" position
8. If necessary, allow pump to prime for 10-30 seconds
by turning the priming/pressure relief valve (#15 on
page 4) 45 degrees to the left to the "O" open posi-
tion.
9. Allow pump to prime
10. Close the Priming valve
11. Turn on the vacuum motor
12. Spray on the backstroke and do a dry stroke when
pushing forward.
13. Overlap your previous path slightly when you pull
back
14. Monitor the levels in the recovery tank and empty
as necessary. Use defoamer to ensure your vacuum
motor does not take in fluid
NOTE: The CR2 Chemical system does not apply chem-
ical in carpet mode. You may use traditional in-tank or
prespray methods.
11