- ページ 7

ソウ djm direct DJMSL12のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。djm direct DJMSL12 15 ページ。 12 double bevel compound sliding mitre saw

ページを印刷する

Always tighten the locking knob (10)&(18) firmly before sawing.

Otherwise the saw blade can become wedged in the workpiece.

Stationary or Flexible Mounting

To ensure safe handling, the machine must be mounted on a level

and stable surface (e. g., workbench) prior to using.

Mounting to a Working Surface

– Fasten the power tool with suitable screw fasteners to the working

surface. The mounting holes (14)serve for this purpose.

– Clamp the power tool with commercially available screw clamps by

the feet to the working surface.

Mounting to a Saw Stand

Any universal saw stand which will accept mounting holes 420mm

wide by 350mm in length will suffice

Read all safety warnings and instructions included with the

worktable. Failure of observing safety warnings and instructions can

lead to electrical shock, fire and/or cause serious injuries.

Assemble the worktable properly before mounting the power tool.

Perfect assembly is important in order to prevent the risk of

collapsing.

– Mount the power tool in transport position on the saw stand.

Dust/Chip Extraction

Dusts from materials such as lead-containing coatings, some wood

types, minerals and metal can be harmful to one's health. Touching

or breathing-in the dusts can cause allergic reactions and/or lead to

respiratory infections of the user or bystanders.

Certain dusts, such as oak or beech dust, are considered as

carcinogenic, especially in connection with wood-treatment additives

(chromate, wood preservative). Materials containing asbestos may

only be worked by specialists.

– Always use dust extraction or the Dust bag (21) provided

– Provide for good ventilation of the working place.

– It is recommended to wear a P2 filter-class respirator.

Observe the relevant regulations in your country for the materials to

be worked.

The dust/chip extraction can be blocked by dust, chips or workpiece

fragments.

– Switch the machine off and pull the mains plug from the socket

outlet.

– Wait until the saw blade has come to a complete stop.

– Determine the cause of the blockage and correct it.

Integrated DustExtraction.

– Insert the dust bag firmly onto the machine

During sawing, the dust bag must never come in contact with moving

tool components.

Always empty the dust bag in good time.

External Dust Extraction

For dust extraction, you can also connect the extraction port (25) to a

vacuum hose (internal Ø 40 mm).

The dust extractor must be suitable for the material being worked.

When vacuuming dry dust that is especially detrimental to health or

carcinogenic, use a special dust extractor.

Changing the Blade

Before any work on the machine itself, pull the mains plug.

When mounting the saw blade, wear protective gloves. Danger of

injury when touching the saw blade.

Use only saw blades whose maximum permitted speed is higher than

the no-load speed of the power tool.

Use only saw blades that correspond with the characteristic data

given in these operation instructions.

Use only saw blades recommended by the tool manufacturer, and

suitable for sawing the materials to be cut.

Removing the Saw Blade

– Bring the power tool into the working position.

– Press lever (4) and swing back the retracting blade guard (5) to the

stop.

Hold the retracting blade guard in this position.

– Loosen both screws (26). This then releases blade guard (5).

– Lower blade guard (5) down to rest on saw table (13).

– Turn blade bolt (27)with the provided blade wrench(41) and at the

same time press the blade spindle lock (23)until it engages.

– Keep the blade spindle lock (23) pressed and unscrew blade bolt

(27)in clockwise direction (left-hand thread!).

– Mount the clamping flange (28) and blade bolt (27). Press spindle

lock (38 ) until it engages, and then tighten the blade bolt with a

tightening torque of approx. 15–23 Nm turning in anticlockwise

direction.