- ページ 4
エクステンダー Altronix AL1002ULADAのPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Altronix AL1002ULADA 17 ページ。 Nac power extenders
Altronix AL1002ULADA にも： インストレーション・マニュアル (13 ページ), アプリケーション・マニュアル (8 ページ), アプリケーション・マニュアル (8 ページ), アプリケーション・マニュアル (8 ページ)
ページを印刷する
6. Connect FACP output to the desired AL842LGK logic board inputs, and notification appliances to the desired AL842LGK
logic board outputs (see Application Guide).
Note: The 2-wire horn/strobe sync mode will only synchronize horns, horn/strobes, strobes with
synchronization capability.
7. For connection of smoke detectors, digital dialer see Optional Hookup Diagram, pg. 8.
Outputs must be programmed independently (OUT1 - OUT4)
Function
Input to Output Follower
Mode
Temporal Code 3 Mode
Steady Mode
For the above modes Dip Switch 4 determines which Input controls the corresponding output:
Switch 4 in the ON position causes output(s) to be controlled by input 1.
Switch 4 in the OFF position causes output(s) to be controlled by input 2.
Switch Positions
Function
Amseco Sync
Mode*
Faraday
Sync Mode*
Gentex
®
Sync Mode
Gentex is a registered trademark of
Gentex Corporation.
System Sensor
®
Sync Mode*
1, 2, 4
System Sensor is a registered
trademark of Honeywell.
CooperWheelock
®
Sync Mode*
2, 3, 4
CooperWheelock is a
registered trademark of
Cooper Wheelock.
Note: The AL1042ULADA will only synchronize horns, horn/strobes and strobes that contain synchronization capability.
Contact signal manufacturer for more detailed info. The same synchronization mode must be selected for all outputs.
Note: It is required to control visual notification appliances (strobes) via input 1 [IN1] and audible notification
appliances (horns) via input 2 [IN2]. This allows audible notification appliances (horns) to be silenced while
visual notification appliances (strobes) continue to operate.
- 4 -
Output Programming Selection Table:
Switch Positions
ON
OFF
1
2, 3
3
1, 2
1, 2, 3
Sync Mode Selection Table:
Descriptions
ON
OFF
This mode is designed to work with the Amseco series of horns, strobes, and
1, 3,
horn/strobes to provide a means of synchronizing the Temporal-coded horns,
2
4
synchronizing the flash timing of the strobe, and silencing the horns of the horn/
strobe combination over a two-wire circuit while leaving strobes active.
This mode is designed to work with the Faraday series of horns, strobes, and horn/
strobes to provide a means of synchronizing the Temporal-coded horns, synchroniz-
2, 4
1, 3
ing the flash timing of the strobe, and silencing the horns of the horn/strobe combi-
nation over a two-wire circuit while leaving strobes active.
This mode is designed to work with the Gentex
1, 2,
strobes to provide a means of synchronizing the Temporal-coded horns, synchroniz-
3, 4
ing the flash timing of the strobe, and silencing the horns of the horn/strobe combi-
nation over a two-wire circuit while leaving strobes active.
This mode is designed to work with the System Sensor
horn/strobes to provide a means of synchronizing the Temporal-coded horns, syn-
3
chronizing the one-second flash timing of the strobe, and silencing the horns of the
horn/strobe combination over a two-wire circuit while leaving strobes active.
This mode is designed to work with the CooperWheelock series of horns, strobes,
and horn/strobes to provide a means of synchronizing the Temporal-coded horns,
1
synchronizing the one-second flash timing of the strobe, and silencing the horns of
the horn/strobe combination over a two-wire circuit while leaving strobes active.
Descriptions
Output follows signal it receives from the corresponding input
(i.e. FACP Sync module - maintains synchronization of
notification appliance circuit).
Enables Temporal Code 3 signal generation output.
This mode will accept a steady or a pulsing input.
A steady output signal will be generated.
This mode will accept steady or pulsing input.
AL842LGK Board
(Output Dip Switches)
series of horns, strobes, and horn/
®
series of horns, strobes, and
®
INPUT SELECT
TEMPORAL
STROBE SYNC
IN>OUT SYNC
AL1042ULADA