- ページ 13

ソウ Custom Dynamics DCS777のPDF マニュアルをオンラインで閲覧またはダウンロードできます。Custom Dynamics DCS777 17 ページ。

ページを印刷する

Bench Mounting (Fig. B)

1. Holes

are provided in all four feet to facilitate bench mounting.

Bolts with a diameter of 8 mm and 80 mm in length is suggested.

Always mount your saw firmly to prevent movement. To enhance the

portability, the tool can be mounted to a piece of 12.5 mm or thicker

plywood which can then be clamped to your work support or moved to

other job sites and reclamped.

2. When mounting your saw to a piece of plywood, make sure that the

mounting screws do not protrude from the bottom of the wood.

The plywood must sit flush on the work support. When clamping the

saw to any work surface, clamp only on the clamping bosses where

the mounting screw holes are located. Clamping at any other point will

interfere with the proper operation of the saw.

3. To prevent binding and inaccuracy, be sure the mounting surface is

not warped or otherwise uneven. If the saw rocks on the surface, place

a thin piece of material under one saw foot until the saw is firm on the

mounting surface.

Mounting the Saw Blade (Fig. A, D, E)

WARNING: To reduce the risk of injury, turn unit off and

disconnect machine from power source before installing and

removing accessories, before adjusting or changing set-ups

or when making repairs. Be sure the trigger switch is in the OFF

position. An accidental

start-up can cause injury.

WARNING: The teeth of a new blade are very sharp and can

be dangerous.

WARNING: Be aware the saw blade shall be replaced in the described

way only. Only use saw blades as specified under Technical Data;

Cat.no.: DT4320 is suggested.

1. Insert the 6 mm hex key

shaft and hold it (Fig. D).

2. Use second hex key as shown in Figure D as spindle lock.

3. Loosen the blade bolt

by turning clockwise. Remove the blade bolt

and the outer flange

4. Press the lower guard lock up release lever

guard

and remove the saw blade

5. Install the new saw blade onto the shoulder provided on the inner

flange

making sure that the teeth at the bottom edge of the blade

are pointing towards the fence (away from the operator).

6. Replace the outer flange

, making sure that the location lugs

engaged correctly, one on each side of the motor shaft.

7. Tighten the blade bolt

by turning anti-clockwise while holding the

6 mm hex key

engaged with your other hand (Fig. D).

ADJUSTMENTS

WARNING: To reduce the risk of serious personal injury, turn

machine off and disconnect battery pack before making any

adjustments or removing/installing attachments or accessories.

An accidental start-up can cause injury.

Your mitre saw was accurately adjusted at the factory. If readjustment

due to shipping and handling or any other reason is required, follow the

steps below to adjust your saw. Once made, these adjustments should

remain accurate.

Adjusting the Traverse Bars for Constant Cutting

Depth (Fig. A, B, F, H)

The blade must run at a constant cutting depth along the full length of the

table and must not touch the fixed table at the rear of the slot or at the front

of the rotating arm. To achieve this, the traverse arms must be perfectly

parallel to the table when the saw head is fully depressed.

1. Press the lower guard lock up release lever

into the opposite location of the blade

to raise the lower blade

(Fig. A).

2. Press the saw head fully to the rear position and measure the height

from the rotating table

3. Turn the saw head traverse lock

4. Keeping the saw head fully depressed, pull the head to the end of

its travel.

5. Measure the height indicated in figure F again. Both values should

be identical.

6. If adjustment is required, proceed as follows (Fig. H):

a. Loosen the locknut

as required, proceeding in small steps.

b. Tighten the locknut

WARNING: Always check that the blade does not touch the table at

the rear of the slot or at the front of the rotating arm at 90° vertical

and 45° bevel positions. Do not switch on before having checked this!

Adjusting the Fence (Fig. I)

Turn the sliding fence lock knob

sliding fence

to a position that avoids the blade cuts it,then tighten the

fence lock knob by turning clockwise.

Checking and Adjusting the Blade to the Fence

(Fig. B, J, K)

1. Slacken the mitre latch

2. Place your thumb on the mitre arm

to release the rotating table/mitre arm

3. Swing the mitre arm until the latch locates it at the 0° mitre position.

4. Pull down the head and lock it in this position using the lock down

button

5. Check that the two 0° markings

just visible.

6. Place a square

WARNING: Do not touch the tips of the blade teeth with the square.

7. If adjustment is required, proceed as follows:

a. Loosen the screws

or right until the blade is at 90° to the fence as measured with the

square (Fig. J).

b. Retighten the screws

Checking and Adjusting the Blade to the Table

(Fig. L–N)

are

1. Loosen the bevel clamp handle

2. Press the saw head to the right to ensure it is fully vertical and tighten

the bevel clamp handle.

3. Place a set square

WARNING: Do not touch the tips of the blade teeth with the square.

4. If adjustment is required, proceed as follows:

a. Loosen the bevel clamp handle

adjustment stop screw

table as measured with the square.

b. If the bevel pointer

scale

, loosen the screws

scale as necessary.

Checking and Adjusting the Bevel Angle (Fig. A, L, N)

The bevel override allows the max. bevel angle to be set at 45° or 48°

as required.

•

Left = 45°

•

Right = 48°

1. Make sure the override knob

2. Loosen the bevel clamp handle

to the bottom of the outer flange

(Fig. B).

in the bracket

and adjust the screw

anti-clockwise to loosen. Move the

and squeeze the mitre latch

on the mitre scale

against the left side of the fence

and move the scale/mitre arm assembly left

(Fig. L).

on the table and up against the blade

and turn the vertical position

in or out until the blade is at 90° to the

does not indicate zero on the bevel

that secure the scale and move the

is located in the left position.

and move the saw head to the left.

EnGLIsh

(Fig. F).

are

and blade

(Fig. M).