- ページ 2
潤滑システム DLS 125のPDF クイックスタートをオンラインで閲覧またはダウンロードできます。DLS 125 2 ページ。 Car audio speakers
DLS 125 にも： マニュアル (4 ページ), オーナーズマニュアル (4 ページ), クイックスタート (2 ページ), クイック・スタート・マニュアル (4 ページ)
ページを印刷する
This brief instruction of mounting the FlexxPump 125 time
addresses to experienced users. Please visit
www.dls-schmiersysteme.de to download the complete user
manual including all safety instructions.
1. Product details FlexxPump 125 time
0
1
7
2
6
3
5
4
No.
Description
0
FlexxPump 125 time
1
LCD
2
Operation pad (for actions with the APK
3
Electric interface M12x1
4
Activation and programming key (APK)
5
Lubricant outlet / M16 male thread for bottom mounting
6
M5 female thread for bottom mounting
7
Serial number
8
M5 female thread for rear mounting
9
Cartridge sensor
10
Lubricant inlet with thread for cartridge
11
Nameplate with designation and CE mark
2. Technical data
Housing
Mounting options
backside: female thread M5 (2x)
bottom: f. thread M5 (1x), m. thread G1/4(1x)
Max. Torque mounting
3
Mounting position
upright
Operating temperature
-10 till +60
Lubricant and hydraulic
Number of lubrication
up to 4 by using splitters*
points
up to 10 by using progressive distributors*
Max. Pressure
50 (-10 % / +15 %)
Grease delivery
Per stroke 0,15
Electrics
Operating voltage
24 (20...28)
Protection
0,75 (slow blow)
Protection class
IP 54
* The stated value is down to the individual application and may extensively differ in
some cases (depending on the lubricant and further conditions).
3. Mounting
8
1.
Remove the yellow protective cap from the top of the lubricant inlet of
the FlexxPump 125 time.
2.
Unscrew the yellow protective cap counterclockwise from the lubricant
9
outlet on the bottom of of the FlexxPump 125 time. Remove the black
protective cap from the electrical interface on the bottom of the
10
FlexxPump 125 time.
3.
To connect the FlexxPump 125 time with an external power supply
system add a proper connecting cable to the electrical interface on the
11
bottom.
4.
Turn the cap on the lubricant cartridge counterclockwise and pull it off.
5.
Place the full lubricant cartridge with the label up front on the
FlexxPump 125 time. Turn the lubricant cartridge
the FlexxPump 125 time.
Damaged or flawed electrical connections or unlicensed hot
components lead to heavy injuries or even death.
4. Commissioning
1.
Mechanical fastening
Fix the FlexxPump 125 time mechanically through the M5 female threads
or through the
attention to the maximum tightening torques permissible for the M5
female threads!
2.
Electrical connection
3.
Power on
4.
Execute FIL function
5.
Hydraulic connection
Connect the consumer hydraulically to the FlexxPump 125 time. If you
connect tubes to the FlexxPump 125 time, make sure that tubes and
Nm
connectors are installed tightly, cleanly and correctly.
Ideally, use tubes prefilled with the appropriate lubricant.
6.
Check the settings on the FlexxPump 125 time
°C
Check the required values for the lubrication point at the factory settings
of the FlexxPump 125 time and adjust them if necessary.
Factory settings: operating mode=hour mode.
5. Operation and settings
bar
Two operating modes can be selected.
cm³
The hour mode -h- allows setting the number of cycles (c) within a break time
(h) in hours. The cycles are evenly distributed over the break time. Break times
between 1...240 hour(s) and cycles between 1...10 can be set.
V
The empty time mode Et allows the emptying time of the cartridge to be set
A
in months. Emptying times between 1...24 month(s) can be set.
5.1 Default settings, operating mode: hour mode -h-
Pause time
number of cycles
LCD
twice
clockwise onto
DANGER
male thread of the lubricant outlet. Pay particular
G1/4
h = 6
The break time is 6 hours.
c = 1
The number of cycles is one (1) stroke
during break time.
5.2 Menu and LCD messages
The graphic above illustrates the unchangeable basic flowchart of the the
FlexxPump 125 time menu navigation as well as the options for branching to
sub-menus.
The FlexxPump 125 time can be switched on and off at several points in the
menu navigation.
The INF menu provides you with an informative overview of the current the
FlexxPump 125 time settings.
The SET menu allows you to make change the operating mode and to
adjust the size of the cartridge.
The RUN menu allows you to manually trigger a single dispense at the
FlexxPump 125 time.
The PRO menu allows you to make changes to the the FlexxPump 125 time
settings and thus to its dispensing behavior.
The FIL menu allows you to manually trigger a fixed number of dispenses
at the FlexxPump 125 time.
Display in LCD
Description
Errors
E1
Error E1 (empty cartridge / cartridge error)
E2
Error E2 (overload / overpressure)
E3
Error E3 (undervoltage)
E4
Error E4 (fatal error)
Submenus
INF
INF-menu
n11
Firmware version of the FlexxPump 125 time
h06
Currently set value of break time h
c01
Currently set value of number of strokes c
06
Currently set value of emptying time Et
125
Currently set value of cartridge size
SET
SET-menu
-h-
Operating mode: hour mode
Et
Operating mode: empty time mode
125/250
Changeable value of catridge size