- ページ 2
屋外ライト ACQUA SOURCE WPLD-6R162-PBMのPDF インストレーション・インストラクションをオンラインで閲覧またはダウンロードできます。ACQUA SOURCE WPLD-6R162-PBM 2 ページ。 Wall mounted lamp
ページを印刷するDIMENSION
DIMENSION
DIMENSION
INSTALLATION
1. Input voltage is AC12V. The lamps must be connected with transformer.
2. The junc�on box is located at least 1200mm from the edge of the pool.
INSTALLATION
INSTALLATION
MINI 1200mm
1. Input voltage is AC12V. The lamps must be connected with transformer.
1. Input voltage is AC12V. The lamps must be connected with transformer.
Junc�on Box
2. The junc�on box is located at least 1200mm from the edge of the pool.
2. The junc�on box is located at least 1200mm from the edge of the pool.
MINI 1200mm
Junc�on Box
Junc�on Box
Rigid conduit
Rigid conduit
Figure 1
3. The moun�ng bracket must be properly installed so that the top edge of the
3. The moun�ng bracket must be properly installed so that the top edge of the
3. The moun�ng bracket must be properly installed so that the top edge of the
light's lens is at least 450mm below the water level in the pool. see Figure 1.
light's lens is at least 450mm below the water level in the pool. see Figure 1.
light's lens is at least 450mm below the water level in the pool. see Figure 1.
Mini. from bo�om of
J.B. to water level
MINI 1200mm
Water Level
Mini. from bo�om of
Mini. from bo�om of
From water level to top of lens
J.B. to water level
J.B. to water level
Water Level
From water level to top of lens
From water level to top of lens
Wall surface
Wall surface
Wall surface
Pool body
Rigid conduit
Pool body
Pool body
250mm
250mm
250mm
Figure 1
Figure 1
2
2
2
4. Make sure the surface of pool wall is flat.
Fix the bracket with 4pcs screws.
4. Make sure the surface of pool wall is flat.
4. Make sure the surface of pool wall is flat.
Fix the bracket with 4pcs screws.
Fix the bracket with 4pcs screws.
5. If the cable connec�on is done underwater, the connec�on part must be
waterproof protected (use waterproof cable gland or fill with epoxy glue).
Otherwise, the water will come in the lamp through the wires.
5. If the cable connec�on is done underwater, the connec�on part must be
5. If the cable connec�on is done underwater, the connec�on part must be
waterproof protected (use waterproof cable gland or fill with epoxy glue).
waterproof protected (use waterproof cable gland or fill with epoxy glue).
Otherwise, the water will come in the lamp through the wires.
Otherwise, the water will come in the lamp through the wires.
6. Connect all wires to the corresponding circuit wires in the junc�on box and
feed epoxy.
7. Before opera�ng the light for more than 10 seconds fill pool un�l the light is
6. Connect all wires to the corresponding circuit wires in the junc�on box and
6. Connect all wires to the corresponding circuit wires in the junc�on box and
feed epoxy.
completely submerged in water.
feed epoxy.
7. Before opera�ng the light for more than 10 seconds fill pool un�l the light is
7. Before opera�ng the light for more than 10 seconds fill pool un�l the light is
completely submerged in water.
completely submerged in water.
Water Level
8. It is easy to replace the lamp.
8. It is easy to replace the lamp.
8. It is easy to replace the lamp.
Posición libre
Posición libre
Posición libre
3
FIXTURE
MOUNTING
SCREW LOCATION
SCREW
TOP
7CM FROM
CENTER
FIXTURE
FIXTURE
MOUNTING
MOUNTING
SCREW LOCATION
SCREW LOCATION
SCREW
SCREW
FIXTURE TAB
TOP
TOP
SLOT
CONDUIT
CONDUIT
7CM FROM
7CM FROM
CENTER
CENTER
FIXTURE TAB
FIXTURE TAB
SLOT
SLOT
Posición bloqueada
Posición bloqueada
Posición bloqueada
3
3
CONDUIT