ペットケア製品 DogWatch R7mのPDF 操作説明をオンラインで閲覧またはダウンロードできます。DogWatch R7m 2 ページ。 Hidden fences performance series systems

ページを印刷する

R7m and R9 Receiver

Contact Posts

Adjustable

Nylon

Collar

3.6 Volt Battery (R9)

Battery Cap

The components of both the R9 (above) and the R7m are the same except the R7m

is smaller and uses a different battery.

Receiver Battery

Both the R7m and the R9 operate on a replaceable battery. Both receivers are water-

proof when the battery cap is fully seated.

R9 Battery: The R9 receiver is powered by a 3.6 volt lithium battery. With normal use,

the battery should last about two years. The positive (+) end of the battery must be

inserted down.

R7m Battery: The R7m receiver is powered by a 3 volt (1/3 N) lithium battery. With

normal use, the battery should last about six months. The negative (-) end of the

battery must be inserted down.

Insert battery POSITIVE end down.

Resetting the Battery Status Light

1. Remove the old battery.

2. Let the receiver sit for five minutes before inserting a new battery.

3. Insert a new battery.

If you forget to wait prior to inserting a new battery, the flashing red battery

status light will continue to flash for 24 hours before automatically resetting.

Battery Plans: Ask your DogWatch Dealer about a battery plan. If your Dealer does not

offer a battery plan, you can join the DogWatch Battery Program, where a new battery is

mailed to you every 6 or 24 months, depending on the type of receiver you own. Call

DogWatch at 800-793-3436 or join through the website at www.dogwatch.com.

Metal Lock Washer

CollarBone

Test Light

Magnet

Marks on receiver indicate where

to hold magnet to change setting

Insert battery NEGATIVE end down.

R 7 m and R 9 Receiver Features

AutoMemory™ When the receiver is set to one of the AutoMemory levels, our patented

AutoMemory feature automatically adjusts the correction level of the receiver when your

pet challenges the boundary by entering the avoidance zone. When this happens, the

receiver will automatically advance the correction level setting by one level. If the dog does

not enter the signal field again in the next 24-hour period, the receiver defaults to the

original setting. The AutoMemory feature operates when your Receiver Training Level is

set to 4, 5, or 6.

Status Light

Start-Up When you first insert the battery into your receiver, the status light will flash

red and green. This indicates that the receiver has started properly. Once started, the

status light will continue to flash green once every 30 seconds indicating normal

operation. In the event that the light does not flash, check the battery to be sure that it

has been inserted properly.

Training Level Indicator When programming the training level of your receiver, the

status light will flash green in conjunction with audible beeps. The number of flashes

will equal the training level you have chosen.

Signal Field Indicator When testing the receiver in the signal field the status light will

flash green when the receiver is in the audible zone and will flash green and red when

the receiver is in the correction zone.

Correction Alert You will be able to tell if your pet has tested the boundary by looking

at the status light. The status light will double flash green every 30 seconds during the

24-hour period after the dog has entered the boundary area.

Battery Indicator This feature monitors the voltage level of the battery. Once the

receiver detects that the battery has reached a low voltage level, the status light will

change from the normal blinking "green" every 30 seconds to blinking "red" every 10

seconds. This indicates that your battery is close to the end of its useful life and you

should change the battery within the next 3-4 days.

SETTING THE RECEIVER

Receiver Training Levels Your receiver provides eight training levels that allow you to

customize the training setting to your dog's individual needs: Audible Only, Level 1 (extra

low), Level 2 (low), Level 3 (low medium), Level 4 (medium), Level 5 (medium high), Level 6

(high), and Level 7 (extra high). When the receiver is first shipped from the manufacturer, it

will automatically be set to Training Level 2 (low).

Changing the Receiver Settings If you need to change the Training Level on the receiver,

hold your test light magnet to the marked area on the side of the receiver. Hold the magnet

steady and you will hear a series of beeps that indicate the current training level. The

"Audible Only" level is one long beep, Level 1 is one short beep, Level 2 is two short

beeps, Level 3 is three short beeps, etc. The Training Level will continue to advance while

the magnet is held in position. When you reach the desired setting, pull the magnet away

from the receiver. The receiver is now set.

Using the magnet to reset the R7m.

Using the magnet to reset the R9.