- ページ 2

コントロールユニット DOLD INFOMASTER SMS RP 5812のPDF モニタリング技術をオンラインで閲覧またはダウンロードできます。DOLD INFOMASTER SMS RP 5812 4 ページ。 Sms-telecontrol module

ページを印刷する

Indication

green LED „U

yellow LED „GSM"

off:

flashes 600ms on / 600 ms off: SMS-Tele control module searches for

flashes 75ms on / 3s off:

on:

yellow LED „Status"

off:

flashes:

on:

Settings

Safety remarks

• The SMS-Telecontrol module must not be used for safety relevant

control functions due to signal availability.

• The use of the SMS-Telecontrol module in medical rooms must

be evaluated thoroughly as medical equipment such as pacema-

kers etc may react to the radiofrequency of the SMS-Telecontrol

module. Also be aware that the radio frequency of the SMS-Tele-

control module may disturb the function of insufficiently protected

PCs, monitors and other electronic equipment.

• Delays in the transmission of I/O status may take place due to

network problems.

General settings

• If the SMS-Telecontrol module is disconnected for a long period, (e.g. as

when delivered) the battery must be charged. To do this the SMS-Tele-

control module needs to be connected to the supply Voltage for up to 6 h.

Only after this time is correct operation is possible.

Attention

On delivery the battery is disconnected. Before the batteries can

be charged the connection has to be made by changing the slide

switch at the bottom edge of the unit to the ON position.

• On first activation a SIM card with a pin code of 1234 has to be inserted.

This pin can then be changed by an SMS command. After pin change

only the SIM card with the changed pin can to be used. If the pin number

on the SIM card is different to the one in the configuration the SIM card

may be locked when connecting to the GSM network. A locked SIM card

can be unlocked by placing it in a mobile Phone and entering the PUK

or Master pin.

• If the Reset/Default Konf. button on the front of the unit is pressed for 3-4

seconds while the unit is powered up, the SMS-Telecontrol module is reset.

This means, that the any connection to an SMS network is disconnected

and reconnected. If the reset button is pressed for more than 5 sec the

configuration is reset to default and the unit makes a factory reset.

• Due to the internal battery back up, the function of the SMS-Telecontrol

module is still available even if the power supply is disconnected for up

to 24 hours.

Attention

It is your responsibility as an end user to dispose old batteries

correctly. Of course, you may return replaced batteries to us.

on when supply connected

SMS-Telecontrol module is off

available network and logs on

SMS-Telecontrol module is registered on

GSM

network.

Data transmission in GSM network

is taking place

Configuration correct,

SMS-Telecontrol module is working

correctly

Indication of failure code, see table

"Fault indication by flashing code"

SMS transmission take place

Settings

Set up procedure of SMS-Telecontrol module

• Wire the i/p's- o/p's and the auxiliary supply connections

• Press the SIM eject button (use pen tip), insert the SIM-card with the

Preconfigured pin 1234 into the SMS-Telecontrol module

• Power up the SMS-Telecontrol module

• Send the necessary configuration commands via text to the

SMS-Telecontrol module (see manual)

Examples for configuration and communication of the SMS module

via SMS:

Demand:

The SMS module located in the pump station, should be named

"Pump station" and then answer with this name.

The following SMS is created and sent:

CFGDN§Pump station#

Demand:

Input I0 shall send an SMS on the negative edge (turning off)

of the input signal

The following SMS is created and sent:

DISEND§0§FE#

Demand:

Input I0 shall be named „ Pump"

The following SMS is created and sent:

DISYMB§0§Pump#

Demand:

The status „0" of input I0 shall be named „ Pump stopped"

The following SMS is created and sent:

DITXTLO§0§Pump stopped#

An SMS is generated and sent by the SMS module caused by a defective

Pump,it appears as follows:

Answer: „Pump station:Pump stopped"

Demand:

The current status of the (2 or 4) digital inputs can be called up.

The following SMS is created and sent:

?DIALL#

Answer: „Pump station:Pump stopped; Level to high"

and for the 2 analogue inputs:

and to call up the 2 analogue inputs if previously configured for level and

motor temperature

?AIALL#

Answer: „Pump station: Level:180cm; pump temp: 85°C"

Safety notes

Attention: • It is important, that the connected voltage of the analogue

inputs and tha analogue outputs of the variant /001 are no

larger that are spezified in the Technical Data.

• The Li-Ion battery can not be changed by the user.

Is there a need to replaced the battery please send the

device back to the manufacturer.

•

Please note, before using, the other safety instructions of

the manual INFOMASTER SMS-Telecontrol module RP 5812.

Technical Data

Input

Auxiliary Voltage A1-A2 (U

): DC 24 V,

Nominal consumption A1-A2: max. 4.5 W at DC 24V

Inputs (digital)

RP 5812:

RP 5812/001:

Inputs (analogue)

RP 5812/001:

4 x i/p; I0 ... I3

DC 24 V with galvanic separation

2 x i/p; I0 ... I1

DC 24 V with galvanic separation

2 x i/p; AI0 ... AI1

DC 0 .. 10 V resolution 100 mV

22.02.13 en / 313