Asko W6441 사용 및 관리 매뉴얼 - 페이지 4

{카테고리_이름} Asko W6441에 대한 사용 및 관리 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Asko W6441 20 페이지. User manual use & care guide fr
Asko W6441에 대해서도 마찬가지입니다: 빠른 시작 매뉴얼 (2 페이지), 기획 및 디자인 매뉴얼 (19 페이지), 서비스 매뉴얼 부록 (10 페이지), (스페인어) 사용 및 관리 가이드 (20 페이지), (프랑스어) Manuel D'utilisation Et D'entretien (20 페이지)

페이지 인쇄
Asko W6441 사용 및 관리 매뉴얼
INST
INST
INST
INSTALLA
INST
ALLA
ALLA
ALLA
ALLATION INSTR
TION INSTRUCTIONS
TION INSTR
TION INSTR
TION INSTR
Read these instructions carefully and completely before
you install the machine. The installation should be
carried out by a qualified person who is familiar with all
local codes and ordinances for electrical and plumbing
connections.
SPECIFICA
SPECIFICATIONS
SPECIFICA
TIONS
TIONS
TIONS
SPECIFICA
SPECIFICA
TIONS
Height
33-1/2"–34-1/2 (850–876 mm)
Width
23-7/16" (595 mm)
Depth
23-7/16" (595 mm)
Weight
167 lbs. (73 kg)
Rated load
See data plate
Supply voltage
Single-phase 230 V, 60 Hz
Heating element
2000 W
Fuse
15 A (2 internal fuses)
REMOVING
REMO
REMO
VING
VING
VING THE SHIPPING
THE SHIPPING
THE SHIPPING
THE SHIPPING
REMO
REMO
VING
THE SHIPPING
SUPPOR
SUPPOR
TS
TS
SUPPOR
SUPPOR
SUPPORTS
TS
TS
The machine is transported with three shipping supports,
as illustrated below. These supports hold the tub in place
during shipment. When you unpack the machine, you
must remove these supports.
To remove the shipping supports, follow the instructions
below:
1.
bolts holding the supports in
place and remove the bolts.
You must remove the shipping
supports before you install the
washer.
2.
t h e n
pull
out
t
slot.
3. Rotate the spacer so that
the extruded end points
toward the machine.
4. Insert it into the slot and
push down to lock it into
ACCESSORIES
ACCESSORIES
ACCESSORIES
ACCESSORIES
ACCESSORIES
position.
LEVELING THE
LEVELING THE
LEVELING THE
LEVELING THE
LEVELING THE
MA
MA
MACHINE
CHINE
CHINE
CHINE
MA
MA
CHINE
It is important that the machine is level so it won't vibrate
excessively during the spinning cycles. Each foot on
the washer is adjustable, so you can level the washer
Page 4
UCTIONS
UCTIONS
UCTIONS
UCTIONS
Unscrew the 5/8" (12 mm)
Push the rubber spacer up
it
of
h
e
1
IMPORTANT NOTE:
Cosmetic damage must be reported to your dealer
within five days from the date of purchase. After
unpacking the washer, thoroughly check the unit for
cosmetic damage.
Drum and Barrel
Stainless steel
Outer casing
Stove-enamelled hot-dipped
galvanized steel or stainless steel
Mounting
Four adjustable rubber-covered
feet
Inlet supply hose
5 ft. (1.5 m) PEX tubing with
brass ferrules
Supply pressure
15–142 PSI
Outlet hose
5.5 ft. (1.7 m) polypropylene hose,
3/4" ID
on any surface. Once it is level, securely tighten the lock
nuts on the feet to prevent excessive vibration during
the spin cycles.
WA
WATER SUPPL
WA
TER SUPPL
TER SUPPLY CONNECTION
TER SUPPL
Y CONNECTION
Y CONNECTION
WA
WA
TER SUPPL
Y CONNECTION
Because ASKO washers have their own heating element,
you only need to have a cold water inlet. The connection
Be sure to tighten the
lock nuts securely when
you level the machine.
should be made by someone who is sufficiently skilled.
Use the hose supplied with the washer.
Water pressure must be in the range of 15–146 PSI.
A tap should be fitted on the water supply pipe.
If a new supply pipe has been installed for the washer,
it should be flushed thoroughly to remove any foreign
particles that might clog the strainer in the water inlet.
NOTE: If unit is installed on a second story, follow local
building codes. We recommend a drip pan be
installed.
Y CONNECTION
Tap
Cold water
supply