AMC XCDie-vt 설치 및 사용 설명서 지침 - 페이지 4

{카테고리_이름} AMC XCDie-vt에 대한 설치 및 사용 설명서 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. AMC XCDie-vt 20 페이지. 24bit / 192khz sampling advanced segment dac, with amc proprietary designed switching mode power supply to cover 100 ~ 240vac

페이지 인쇄

WARNING! INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED.

AVOID EXPOSURE TO BEAM.

VORSICHT! UNSICHTBARE LASERSTRAHLEN TRITT AUS, WENN DECKEL GE FFNET

UND WENN SICHERHEITSVERRIEGELUNG BERBR CKT IST. NICHT DEM STRAHL

AUSSETZEN.

ADVARSEL- USYNLIG LASERSTR LING VED BNING, N R SIKKERHEDSAFBRYDERE

ER UDE AF FUNKTION. UNDG UDS TTELSE FOR STR LUNG.

ADVARSEL- USYNLIG LASERSTR LING N R DEKSEL PNES OG SIKKERHEDSL S

BRYTES. UNNG EKSPONERING FOR STR LEN.

VARNING- OSYNLIG LASERSTR LNING N R DENNA DEL R PPNAD OCH SP RRAR

R URKOPPLADE. STR LEN R FARLIG.

VA R O ! - AVAT TA E S S A J A S U O J A L U K I T U S O H I T E T TA E S S A O L E T A LT T l I N A

N KYM T NNT LASERS TEILYLLE. L KATSO S TEESEEN.

CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH THE SAME

TYPE OF T1A/250V FUSES.

ATTENTION: POUR MAINTENIR PROTECTION CONTRE RISQUE D'INCENDIE, UTILISER LES FUSIBLES

DE RECHANGE DE MEME TYPE DE T1A/250V.

THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS

FROM DIGITAL APPARATUS AS SET OUT IN THE RADIO INTERFERENCE REGULATIONS OF THE

CANADIAN DEPARTMENT OF COMMUNICATIONS.

LE PRESENT APPAREIL NUMVERIQUE N'EMET PAS DE BRUITS RADIOELECTRIQUES DEPASSANT

LES LIMITES APPLICABLES AUX APPAREILS NUMERIQUES DE LA CLASSE B PRESCRITES DANS LE

REGLEMENT SUR LE BROUILLAGE RADIO ELECTRIQUE EDICTE PAR LE MINISTERE DES

COMMUNICATIONS DU CANADA.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE

FOLLOWING TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT

MAY CAUSE UNDESIRED OPERATION.

SERVICE SAFETY PRECAUTIONS (UL)

1. Use exact replacement parts for critical locations, marked " ".

2. Return lead dress to original position, and re install protective

covers.

3. Before returning to customer, test for shock hazard; use either

method A or B:

A. Leakage test, "cold":

1. Unplug AC cord; turn power switch ON.

2. Connect one lead of High Voltage Insulation Tester to both prongs

of AC plug.

3. Touch other lead to all exposed metal parts.

4. Impedance measurement must be 0.3-5.0 Megohms.

B. Leakage test, "live":

1. Plug unit directly into AC outlet; do not use isolation transformer.

2. Connect one lead of Leakage Current Tester to earth ground.

3. Touch other lead to all exposed metal parts.

4. Leakage measurement must be less than 0.5 milliamps.

CLASS 1 LASER PRODUCT

LUOKAN 1 LASERPLAITE

KLASS 1 LASERAPPARAT