AMD DIrect SSRFR-24DR2 사용자 설명서 - 페이지 5
{카테고리_이름} AMD DIrect SSRFR-24DR2에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. AMD DIrect SSRFR-24DR2 9 페이지. 2-drawer refrigerator
페이지 인쇄
BEFORE OPERATING
Shipment Arriving Damaged:
VISIBLE DAMAGE
If your shipment arrives with visible damage to the
box/carton, be sure the damage is noted on the
bill of freight or express receipt and signed by the
person making the delivery. File a claim for damages
immediately, regardless of the extent of damage.
CONCEALED DAMAGE
If damages are unnoticed until the refrigerator is
unpacked, notify the transportation company or
carrier immediately and file a concealed damage
claim with them. This should be done within (5)
days of the delivery date. Be sure to hold on to
the box/carton for inspection. We cannot assume
responsibility for damage or loss incurred in transit.
Important Notes:
CONSTRUCTION ZONES
Keep all stainless steel products away from
construction zones. Construction debris such as
(but not limited to) stone dust, stucco, and lime dust
could damage or permanently discolor stainless
steel products. Keep all caustic chemicals including
chlorine and pool cleaning products away from
stainless steel at all times.
BEFORE USING YOUR APPLIANCE
Rmove the exterior and interior packing. Before
connecting the appliance to the power source, let it
stand upright for approximately 24 hours. This will
reduce the possibility of a malfunction in the cooling
system from handling during transportation. Clean
the interior surface with lukewarm water using a soft
cloth. Install the handle on the drawer if not already
attached.
INTERIOR LIGHT
This unit is equipped with an interior LED light which
can be manually turned ON and off by pressing the
The light will automatically turn OFF after closing the
drawers.
DEFROSTING
The unit defrosts automatically in normal operating
conditions. The evaporator behind the rear wall of
the unit defrosts automatically. The condensation
collects in the drainage channel behind the rear wall
of the unit and flows through the drainage hole into
the drop tray by the compressor where it evaporates.
However, frost may accumulate on the evaporator
if the unit is repeatedly opened in a high heat or
high humidity location. If this frost pattern does not
clear within 24 hours, your unit will require manual
defrosting.
Press
and hold for 6 seconds, the unit will be
defrosted.
To stop defrost, please repeat the same interaction.
1
2-DRAWER REFRIGERATOR USER MANUAL
WARNING
ELECTRICAL PARTS & COMPONENTS
Disconnect all power supplies and batteries
before servicing
TEMPERATURE ALARM
An audible alarm sounds if the storage temperature is
not cold enough. The temperature display flashes at
the same time.
The cause of the temperature being too high may be:
• Too much warm ambient air flow when rearranging
and removing stored items.
• Prolonged power failure.
• The appliance is faulty.
The audible alarm is automatically silenced and
the temperature display stops flashing when the
temperature is sufficiently cold again.
CLEANING AND MAINTENANCE
Periodic cleaning and proper maintenance will ensure
efficiency, top performance and long life.
The maintenance intervals listed are based on normal
conditions. You may want to shorten the intervals if
you have pets or other special considerations.
Exterior cleaning for your stainless steel model.
• Your stainless steel model may discolor when
exposed to chlorine gas, pool chemicals, salt water
or cleaners with bleach.
• Keep your stainless unit looking new by cleaning
with a high quality, all-in-one stainless steel
cleaner/polish on a monthly basis. Frequent
.
cleaning will remove surface contamination that
could lead to rust. Some installations will require
cleaning on a weekly basis.
• DO NOT CLEAN WITH STEEL WOOL PADS.
• DO NOT USE CLEANERS THAT ARE NOT
SPECIFICALLY INTENDED FOR STAINLESS STEEL
(This includes glass, tile and counter cleaners.
• If any surface discolor or rusting appears, clean
it quickly with Bon-Ami or Barkeepers Friend
Cleanser and a non-abrasive cloth. Always clean in
the direction of the grain. Always finish this process
with a high quality, all in one stainless cleaner/
polish to prevent further problems.
• USE OF ABRASIVE PADS SUCH AS SCOTCHBRITE
WILL CAUSE THE GRAINING IN THE STAINLESS
TO BECOME BLURRED.
• Rust that is allowed to linger can penetrate into
the surface of the stainless steel and become
impossible to remove.
TROUBLESHOOTING
Many common problems can be solved easily, saving you the time spent communicating with customer service.
Try the suggestions below to see if the issue has a simple solution.
PROBLEM
POSSIBLE CAUSE
Appliance does not operate.
Appliance is not connected to a power
supply.
The appliance is turned off.
Tripped circuit breaker or a blown a fuse.
Appliance is not cold enough.
The temperature is not set correctly.
Temperature could require a lower
temperature setting.
The drawer was not closed completely.
Drawer is not hermetically sealed.
The condenser is too dirty.
The ventilation opening is blocked or too
dusty.
Appliance turns itself on and off
The room temperature is higher than
frequently.
average.
A large amount of food has been added to
the unit.
The drawer is open too often.
The drawer is not closed completely.
The drawer gasket does not seal properly.
The light does not work.
Appliance is not connected to a power
supply.
Tripped circuit break or blown a fuse.
The light was switched off on the control
panel.
Vibrations.
The appliance is not properly leveled.
The appliance seems to make
The rattling may come from the flow of the
too much noise.
refrigerant, which is normal. As each cycle
ends, you may hear gurgling sounds caused
by the flow of refrigerant in your appliance.
If the temperature fluctuations occur, the
contraction and expansion of the inner walls
may cause popping and cracking noises.
The appliance is not properly level.
The drawer will not close
The appliance is not properly level.
properly.
The drawer was reversed and not properly
installed.
The gasket is dirty.
The alarm sounds and the
Has the appliance drawer been open for
temperature display flashes.
longer than 60 seconds? If not, then the
temperature has risen higher or fallen lower
than the temperature that has been set. This
could be due to:
The appliance drawers being opened too
often. The ventilation opening being covered
or too dusty.
A lengthy interruption in the power supply.
A large amount of food has been added to
the unit.
REMEDY
Connect the appliance.
Switch on the appliance.
Switch on the circuit breaker or replace
fuse.
Check the set temperature.
Set a lower temperature.
Do not open the drawer more often than
necessary.
Close drawer properly.
Check the drawer seal and clean/
replace.
Clean the condenser when necessary.
Clear the obstructions, clean the dust.
Put the appliance in a cooler place.
Leave the appliance to work for a while
until the set temperature has been
reached.
Do not open more than necessary.
Close drawer properly.
Check the drawer seal and clean/
replace.
Connect the appliance.
Switch on circuit breaker or replace
fuse.
Switch on the light.
Level the appliance with the adjustable
feet.
Level the appliance with the adjustable
feet.
Level the appliance with the adjustable
feet.
Check the drawer hinge and reassemble
correctly.
Clean the drawer gasket.
If yes, close the drawer.
Do not open the drawer more often than
necessary.
Clear the obstructions and clean the
dust.
Leave the appliance to work for a while
until the set temperature has been
reached.
2