AMD DIrect Pro Series 설치 및 운영 지침 매뉴얼 - 페이지 5

{카테고리_이름} AMD DIrect Pro Series에 대한 설치 및 운영 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. AMD DIrect Pro Series 20 페이지. Round drop in pan fire pits with thermocouple piloted safety ignition (tpsi) & pro brass snowflake burner
AMD DIrect Pro Series에 대해서도 마찬가지입니다: 설치 및 운영 지침 매뉴얼 (20 페이지), 설치 및 운영 지침 매뉴얼 (20 페이지), 설치 및 운영 지침 매뉴얼 (20 페이지)

페이지 인쇄

Description: These fire pits are designed to be installed into a non-combustible enclosure. They are a "drop-in pan"

style system to make installation quick and convenient. Media (not supplied) is required inside the burner pan for

operation (See page 9).

WARNING: Proper clearances from combustible materials must be maintained from all sides, top and bottom of this

appliance. Use the specifications listed on pages 4 for proper clearance to combustibles.

AMD Direct, Inc fire pits are constructed and tested to follow the rigid ANSI standards for gas appliances and

manufactured safely providing dependable and certified products. If these fire pits are not installed according to the

installation manual (i.e. not providing ventilation, not providing proper drainage, installing fire pits below grade or

modifying the existing products from a normal installation) AMD Direct, Inc cannot be responsible if the product does not

operate as designed.

Modifying the fire pit directly out of the carton will void the warranty and nullify the product listing it was certified for.

Before you consider creating your own custom design with a certified product ensure you contact AMD Direct, Inc to

consult the installation before proceeding. If you move forward and modify a product without consulting, Firegear

Outdoors cannot be responsible if the product does not operate as designed.

The fire pit can be installed on a flat, stable surface, away from any combustible materials. Install fire pit on any level,

outdoor non-combustible, flat stable surface or a combustible floor according to the clearances specified in this manual.

NOTE: Do not place fire pit directly on grass, dirt, or rocks this may prevent proper ventilation. Ensure proper water

drainage is also incorporated into the fire pit enclosure.

HARD PIPING TO FIRE PIT WITHOUT GAS PROXIMITY

NOTE: Refer to the NFPA54 (National Fuel Gas Code) for proper pipe sizing. See gas line sizing chart on page 7 as a

reference.

1. Turn OFF gas supply system. NOTE: All gas connections (except for brass to brass) require the following. Clean pipe

threads using either a wire brush or steel wool. Apply pipe sealant to the fittings before making any connection.

BE CAREFUL! Ensure all gas connections are snug, but do not over tighten!

2. Extend the gas supply system using minimum of ¾" black iron pipe or an approved flexible gas line from existing

house supply. This can be accomplished by teeing off or tapping into a gas line connection. Install necessary pipe for the

distance required and then install a manual shut-off valve at the exterior house wall. If pipe is to pass through a foundation

or house wall, make sure to re-seal the area around the pipe with weather sealant.

3. The primary gas shut-off (not supplied) will require a ½" male flared fitting to enable connection of the stainless steel

flex gas line supplied with the fire pit (see Fig. 7 page 9).

IMPORTANT

Installation of Natural or LP gas should be done by a qualified installer, service agency or gas supplier.

This appliance must be isolated from the gas supply piping system by closing its manual shutoff valve during any

pressure testing of the gas supply piping system at test pressures equal to or less than ½" psig (3.5kPa)

Injectors/Jets - Fire features using a Firegear Pro Series brass burner incorporates individual injectors/jets on each

burner leg. All injectors are protected by a injector cover that is provided with each burner. The injector hole size is

measured by using a numbered drill bit. An injector/jet limits the amount of gas flow to the burner to ensure the flame is a

safe and reasonable height to not pose a risk to people or property. Note: The Firegear Pro Series brass burners DO NOT

USE a primary main burner orifice like a standard stainless steel burner. A steel nipple is installed in place of the primary

burner orifice. Each injector is installed at an angle inside each burner leg to maximize flame appearance.

ALL PAN OR FLAT DISCS MUST BE REMOVABLE FOR SERVICE Pans or Discs CANNOT be installed

in a manner to prevent them from being removed for service. Top coping material or top cap of fire pit

MUST NOT overlap onto the pan or disc surface without easily being removed. Pan lip of disc edge must

be unobstructed so it can be lifted our of the fire pit for servicing. We highly recommend the use of a flex

frame kit for all installations.

Rd. Drop In Pan Fire Pits with Snowflake Burner and (TPSI) Ignition

PREPARING A NON-COMBUSTIBLE STRUCTURE

REV. A

Page 5