AMD Lasers PICASSO 빠른 시작 매뉴얼 - 페이지 7
{카테고리_이름} AMD Lasers PICASSO에 대한 빠른 시작 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. AMD Lasers PICASSO 8 페이지.
AMD Lasers PICASSO에 대해서도 마찬가지입니다: 사용 설명서 (17 페이지)
페이지 인쇄
S T E P 3 | E Q U I P M E N T D E S C R I P T I O N
1
2
4
6
7
8
LANGUAGE SELECTION
The default language is English. Other choices:
Portuguese, Japanese, German, French, Italian,
Spanish, Korean, Chinese, and Russian. To select a
language, depress the desired language button and
hold for two seconds.
VOLUME
Select volume of the beep
5 Levels: Mute, Quiet, Normal, Loud, Very Loud
AIMING BEAM
Select brightness of aiming beam
5 Levels: Off, Weakest, Weak, Strong, Strongest
4
5
3
2
1
SAVING PRESETS:
Each of the three default presets is customizeable. To change a preset from its default value, adjust power up or down to the desired
level, set aiming beam intensity (off, low, high), and speaker volume (off, low, high). Then press and hold the desired preset button for
four seconds until the power display cycles off and on. The new setting for the given preset has been saved.
#
1
2
3
3
4
4
5
5
6
7
8
PICASSO IS PRE-PROGRAMMED FOR SOME PROCEDURES. CHANGING PRESETS:
4 CUSTOM PRESETS ARE AVAILABLE IN
STEP 1:
Continuous Mode: INTERVAL and DURATION are not available. POWER
STEP 2:
STEP 3:
STEP 4:
STEP 5:
STEP 6:
STEP 7:
SPEED MODE:
6
1.8W Continuous Mode
COMFORT MODE:
1.8W Gated (Repeat) Mode
30ms on/off
HYGIENE MODE:
7
0.5W Continuous Mode
8
EASY STEPS TO START:
STEP 1:
Insert tips on the handpiece
9
STEP 2:
Select SPEED, COMFORT, or DIFFUSION
STEP 3:
Select STANDBY/READY button and step on
the foot control to activate the laser
ITEM NAME
ITEM DESCRIPTION
Cont/Rep
Continuous or
Presets
1
2
3
Power
0.5 – 7.0 Watts
Interval
20 ms – 9.9 secs, increments of 10ms
Duration
20 ms – 9.9 secs, increments of 10ms
Settings
Language Selection, Aiming Beam, & Volume Settings
Standby/Ready
Standby or
STAND
BY
Save
Save Button
Select desired type of laser operation mode Continuous or Repeating.
is able to be selected and saved as a preset.
Repeat Mode: all the parameters (INTERNAL, DURATION, and POWER)
are able to be selected as a preset. Use the
interval and duration from 20ms to 9.9 secs.
Select desired preset 1–4.
POWER. Select desired power settings 0.5–7 watts using the left and right
white arrows
INTERVAL/DURATION. Select desired interval and duration (available only
in REP mode).
SAVE. Save desired settings by pushing the SAVE
seconds until a beep is heard.
READY. Push STANDBY button to put unit into READY mode. Press the foot
switch to emit laser.
Repeat steps 1–6 to program additional presets.
#
ITEM NAME & DESCRIPTION
1
Hygiene: Perio Pockets, Aphthous Ulcers, Pulpotomies
2
Comfort Mode: Gingivectomies, Exposing Implants/Brackets/Teeth
3
Speed Mode: Surgery, Troughing, Frenectomies
4
Power Down
5
Power Display
6
Power Up
7
Aiming Beam Intensity: Off / Low / High
8
Volume Setting: Off / Low / High
9
Standby/Ready
Repeating Modes
4
Ready Button
READY
AND
MODES (8 TOTAL):
buttons to select desired
button for two