AME MM-1 사용자 설명서 - 페이지 6

{카테고리_이름} AME MM-1에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. AME MM-1 15 페이지.
AME MM-1에 대해서도 마찬가지입니다: 설치 매뉴얼 (6 페이지), 설치 매뉴얼 (14 페이지)

페이지 인쇄

Auxiliary Output

Trunk Release Output

Pressing button 1 for 3 seconds activates the Trunk Release output. This will issue an impulse on the trunk

release output wire and will override the sensors and trunk input until 10 seconds after the trunk switch is closed,

if you remote open the trunk in armed stage.

Comfort Close Mode

WARNING! This option is not available without a separate Central Door Lock Module being installed.

If you set the programming for the 20 second Locking Pulse, the Central Door Lock Output will be activated for

20 seconds whenever the alarm system is armed either by remote control or by passive arming (not re arming).

During the 20 second close period and for the first 10 seconds after the comfort close period, the sensor will be

disabled. This is to ensure that the sensors cannot trigger the alarm system during the comfort close period and to

allow a 10 second settling period after the close period for the sensors to settle.

System Programming

Remote Code Learning

The AME MM 1 has two transmitters in the standard kit, however the system can teach up to four transmitters

To increase a number of remote controls to control the alarm system fulfill the below procedure:

1. When the alarm system is disarmed enter the PIN Code.

a. Within 7 second switch the ignition on/off twice and then switch it on again.

b. The LED will be flashing quickly. After quick flashing the LED will flash in a rate of one flash per second.

c. Count a number of flashes equal to your PIN Code and switch the ignition off.

d. If the PIN Code is correct the alarm system with double beep will confirm the Remote Code learning

entered.

2. Press button 1 of each remote control you want to program to the system. One siren beep will confirm the

transmitter code is learnt.

3. To exit the Code Learning switch the ignition off and wait for 15 seconds, a double siren beep will confirm that

Code Learning has exited. NOTE: If you want to move to the Function Programming switch the ignition back

on before the double siren beep.

Function programming.

1. Follow through with transmitter programming and turn the ignition back on (before the double siren beep in the

above item 3!).

2. Enter the number of the function that you want to adjust by pressing button one on the transmitter to increase

the number of function or by pressing button 2 to reduce the number of function.

3. Each time the transmitter button is pressed; the siren will beep to indicate the switch that is selected. The

following siren beep sequence will be used: Switch 1 = One short beep, Switch 2 = Two short beeps, ...

Switch 5 = One long beep, ... Switch 7 = One long beep and two short beeps, ... Switch 10 = Two long beeps,

... and so on.

User's Guide

AME MM 1 Car Alarm System

12. ЛИСТ ДЛЯ ОСОБЫХ ЗАМЕЧАНИЙ И ЗАМЕТОК.

Особые замечания при установке:

Особые замечания при эксплуатации:

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

Сведения о проведенных ремонтах и перенастройках с обязательным указанием причин, их

вызвавших, сроков проведения и исполнителей работ:

_ 1 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

________________________________________________________________________________

«___» ______________ _____ г. ___________________________ (подпись владельца СТСТС)

_ 2 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

________________________________________________________________________________

«___» ______________ _____ г. ___________________________ (подпись владельца СТСТС)

_ 3 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

________________________________________________________________________________

«___» ______________ _____ г. ___________________________ (подпись владельца СТСТС)

Владелец ознакомлен с работой СТСТС после ремонта и принял в эксплуатацию

Руководство пользователя

AME MM 1 Автомобильная охранная система