Canon 7816A008AA 간소화된 서비스 매뉴얼 - 페이지 7

{카테고리_이름} Canon 7816A008AA에 대한 간소화된 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Canon 7816A008AA 19 페이지. Bubble jet printer

페이지 인쇄

4. SERVICE MODE

To conduct the following functions, the computer (Windows98/Me), printer driver and service tool

(QY9-0058) for the i320 are needed.

Function

Print head cleaning

< For reference >

Head refreshing (deep

cleaning)

Paper feed roller cleaning

Test printing

1) Nozzle check pattern printing

< For Reference >

Head alignment

2) Shipment pattern printing

- ROM version

- No. of pages fed

- Waste ink amount

- Destination setting

EEPROM reset

Destination setting

(Japan/Others)

Shipment inspection pattern

a. Install the print head (QY6-0044-000), and while holding down the POWER button, plug in the AC cable. (The

green lamp lights.)

b. While holding down the POWER button, press the RESUME button twice, and release it. (Each press of the

RESUME button changes the LED color: the LED lights in orange the first time, and in green at the second time.)

c. Load A4-sized paper.

d. Connect the printer to the computer, select "USB PORT" using the i320 servi ce tool (QY9-0058). (Refer to

Appendix 2, i320 Service Tool.)

e. Select "TEST PATTERN 1". The printer starts printing the shipment inspection pattern.

EEPROM reset / Destination setting

a. Install the print head (QY6-0044-000), and while holding down the POWER button, plug in the AC cable. (The

green lamp lights.)

b. While holding down the POWER button, press the RESUME button twice, and release it. (Each press of the

RESUME button changes the LED color: the LED lights in orange the first time, and in green at the second time.)

c. Connect the printer to the computer, select "USB PORT" using the i320 service tool (QY9-0058). (Refer to

Appendix 2, i320 Service Tool.)

d. <Destination setting>

- Other than Japan:

- Japan:

EEPROM is reset at the same time when the destination is set.

Shipment inspection pattern sample

EEPROM setting can be confirmed from the shipment inspection pattern printout.

ROM Version

i320

P=V X.XX

Destination XX

Page=XXXX

PL=XXXX , HR=XXXX , GP=XXXX , CA=XXXX

SettingTime= XXXX / XX / XX XX:XX YY YY YY YY USB= (YYYYYY)

Select "Cleaning" from the printer driver utility.

Select "Deep Cleaning" from the printer driver utility.

1. Remove the paper from the ASF.

2. Select "Feed Roller Cleaning" from the printer

driver utility.

3. Following the instruction from the status monitor,

load 3 pages of plain paper in the ASF, and feed

them.

Select "Nozzle Check" from the printer driver utility.

1. Select "Print Head Alignment" from the printer

driver utility.

2. Select the optimal value using the printed head

position adjustment pattern.

Refer to Shipment inspection pattern*

Refer to EEPROM reset / Destination setting*

Select "1" in "SET DESTINATION".

Select "2" in "SET DESTINATION".

Destination setting

Other than JPN: 01

JPN:

Unused:

D=XXXXX.X

Installation time

Procedure

below.

Waste ink amount (%)

Remarks

Cleaning time: Approx. 40 sec.

Cleaning time: Approx. 70 sec.

Cleaning time: Approx. 2 min.

Nozzle check pattern printing

Significant misalignment can

be adjusted.

Refer to Shipment inspection

pattern sample*

No of pages fed:

Page: Total No. of pages fed

PL:

Plain paper

HR:

High resolution paper

GP:

Glossy paper

CA:

Postcard

below.