Coaster 900749 조립 지침 매뉴얼

{카테고리_이름} Coaster 900749에 대한 조립 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Coaster 900749 12 페이지. Grandfather clock

페이지 인쇄

900749

ITEM:

STEP 7-1

STEP 10

Operating the clocks as following pictures.

STEP 4-1

Your clock is fitted with a Westminster Chiming movement. This has an automatic night silence function that silences the

1.Solution for not reporting the time with chime:

the hour is signaled, otherwise , repeat the same procedure again. It can be repeated

NOTES: PLEASE MAKE SURE CLOCK IS IN LEVEL POSITION, OTHERWISE

Chimes between 10.00 P.M. and 5.00 A.M.(last strike 9:00PM, first strike 6:00AM).

Regarding the timekeeping and pendulum troubleshooting methods:

a.Rotate the volume button (Figure 2 VOLUME) to the maximum position.

several times to achieve the best results. Finally put back the seconds cap.

IT WILL NOT OPERATE PROPERLY.

* DON'T PUT BATTERIES INTO THE MOVEMENT BEHIND OF PENDULUM DRIVER.

Before the clock leaves the factory, the clock has been set at 5:55AM.

Do not mix Old and New batteries. Do not mix Alkaline, and Standard(Carbon - Zinc) or

Please make sure you have 2 x D Alkaline batteries, as these are not included. You will also need a screwdriver.

b.Check whether the positive and negative positions of the battery are correct (Figure 1). If it

(Note: Keep the two clock hands in parallel position, and they cannot touch each other,

STEP 1-1

■The time cannot be adjusted by adjusting the hour hand (short hand), please turn the

Rechargeable(Nickel - Cadmium) batteries.

ALKALINE BATTERIES REQUIRED

is inaccurate, please reinstall it according to the icon.

neither can touch the face of the clock, nor touch the glass of the front clock)

minute hand (long hand) clockwise.

1.TO START THE CLOCK

c.If the positive and negative poles of the battery are correct and the problem is still not

 Solution 2： Set the time to the time when you hear the time signal, immediately

Lift the up-cover from the back of the top unit(A), you will find a battery holder. Open the

resolved, adjust the time to 5:55 clockwise using the minute hand, remove the battery,

remove the battery, remove the second cap, remove the minute hand, and re-set the

(Note: Turn the minute hand counterclockwise, and cannot go past the 12 o'clock position,

ASSEMBLY TIPS:

battery cover, insert 2 new 1.5 volt "D" alkaline batteries into the Battery Holder and making

Here are a few symptoms that are associated with 'Defective Batteries' or 'Incorrect Installation'

wait for a while, and place it again. Then adjust the minute hand to 6:00 to tell the time

minute hand to the 12 o'clock position, and set the clock to 5:55. position, replace the

1. Remove hardware from box and sort by size.

otherwise it will damage the timekeeping contacts of the movement, resulting in failures

sure the battery is as indicated(picture 1). Push the bob of pendulum(H) leftwards to let the

and do not indicate that the clock itself is defective:

2. Please check to see that all hardware and parts are present prior to start of assembly.

and music.

battery. Automatically or manually dial to 6:00, the hour hand tells the time for 6:00AM.

such as no timekeeping or no music.)

3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.

clock run(picture 3).

Warning!

d.Or use the TIME ADJ button on the battery box (Figure 2) to solve problem (c.) above, each

Then manually adjust to the actual local time, and then install the seconds cap.

Problem

ｈｏｌｅ

2.TO SET TIME:

1. Don't attempt to repair or modify patrs that are broken or defective. Please contact the store immediatelly.

9.If the battery is insuﬀicient, please replace the battery in time.

■Before the clock leaves the factory, the clock hands have been set at 5:55AM. If the clock

time you press, no more than 8 times, you can hear the time and music. The time signaling

Your clock strikes six(6) times on every hour.

2.This product is for home use only and not intended for commercial establishments.

time is obtained on the dial. Do not push too hard or turn the hand counter clockwise (never

Solution

(Note: If the positive and negative poles of any battery are reversed, they must be removed

display is not this time, please turn the minute hand clockwise to adjust to 5:55AM, and then

this time is 6:00 AM. Then use the minute hand to adjust the hour hand clockwise to the

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!

turn the short hand), otherwise it will cause damage of movement(picture 4).

Change the chime section batteries, and set time and chime again by following "SETTING TIME AND

first and then installed again. All are taken down to initialize the clock. Then install it

insert the battery.

actual local time.

STEP 5

CHIME"procedure.

3. TO ADJUST MELODY SELECTION:

2.When there is no music when telling the time, push the sliding button of MELODY SELECT

correctly. It is not possible to mix an old battery with a new battery, let alone replace it with

have the striking sound every hour. The button in position( ): this selection will have both

short chain

STEP 8

■The first chime is set to 6:00 AM. The chime will stop automatically from 10:00 PM to 5:00 AM.

STEP 2-1

Problem

(Figure 2) to the middle position( ).

another type of battery. Be sure to use a large battery of the same model size D. A bad

long chain

the striking sound and Westminster chime every hour. The button in position( ): this

(The night stop function is programmed before leaving the factory. The user cannot change

Your clock starts to chime erratically on every hour.

3.If there is music without telling the time, push the sliding button of MELODY SELECT (Figure

battery can also cause the clock to work infrequently.)

selection will only have the Westminster chime every hour. The clock will not sound from

Solution

it)

10.Possible conditions of the clock caused by insuﬀicient battery power: Inaccurate time

2) to the middle position( ).

PART NAME

Press the "Set" Button of TIME ADJ, the clock will chime, and increase one chime per push, push to

10:00 pm to 5:00 am(picture 2).

4.The time telling time is inconsistent with the displayed time. It can be adjusted by the TIME

reporting, random time reporting, always reporting one time. Or the volume of timekeeping

the correct chime.

4.TO ADJUST TIME:

■Once the battery is removed, the movement will be automatically initialized. After reloading,

If this method still does not solve the problem, replace the chime battery, and set time and chime

and music is getting weaker and weaker. If the battery is low, it will leak, and corrode the

ADJ button (Figure 2) on the battery box. Each time you press it, an hour will be added, and

TOP UNIT

if the clock counts 2 times at 4 o'clock, please press button two times then it gives corrected

the time will be reported again from 6:00 in the morning.

again by following the "SETTING TIME AND CHIME" procedure.

so on. Note that the TIME ADJ key is after 12 o'clock, and it is 1:00 when you press it again.

metal circuit and cause the clock to malfunction. Even damage the battery box. If any of the

pendulum

strike(picture 2).

FURNITURE TIPPING RESTRAINT

5.The hourly timekeeping time is inconsistent with the displayed time. Please set the clock to

above problems are found, replace the battery in time.

Problem

5. TO ADJUST VOLUME CONTROL:

11.If the clock does not report time suddenly, the swing range of the rocker is small or does not

5:55 without placing the battery. After placing the battery, manually or automatically go to

Your clocks chimes are getting quieter and quieter.

FRONT DOOR

desired sound(picture 2).

Solution

6:00, and the clock will show time as 6:00 AM.

swing, the general situation is that the battery power is insuﬀicient, or the connection line

Change the chiming section batteries and turn the volume down to about half way.

6.The time is not reported at 10 o'clock during the day, but reported 10 o'clock at night. The

between the rocker and the battery box is poor, and you need to reinsert it and confirm

STEP 6

STEP 9

whether it is secure.

main reason is that the clock defaults to night as day. You can press the TIME ADJ (Figure 2)

Problem

LEFT SIDE

This restraint is not a substitute for proper adult supervision.

STEP 3

PANEL

12.How to tell the time, the volume is normal, the swing range of the pendulum is unstable, or

button on the battery box for 12 times to change the time to day or night time.

Your clock does not chime at 10 pm.

This restraint may provide protection against tipping furniture.

Solution

7.When the product leaves the factory, the hour hand is set at 5:55. When disassembling the

it shakes, etc. In addition to the battery power attenuation, it is usually caused by the hook

TAKE OFF PAPER LABEL

Your clock has an Automatic night mute with the last strike at 9pm and the first strike at 6am.

protective tape on the movement, you must be careful to avoid touching the pointer and

of the pendulum not hanging to the middle position of the beam of the pendulum rod. In the

RIGHT SIDE

Failure to detach this restraint before moving furniture may

each line to prevent the clock hand from shifting and the line loose.

middle position (Figure 3), and make sure that the pendulum head and the clock body are

PANEL

Problem

8.The solution for the clock not reporting the time on the hour, explain the cause of the

parallel. Don't deviate, twist, etc.

Can I change when the night mute starts and stops?

Solution

13.You need to manually push the pendulum head to the left or right, so that the pendulum

accident. (Note: Do not manually turn the minute hand clockwise too fast. Turn lightly; do not

DESCRIPTION

No, this function is not available.

BATTERY HOLDER

turn for less than 15 seconds. Otherwise, at least the above problems will occur.)

head does not touch the inner wall of the clock case. The pendulum will automatically swing

BOLTφ8*40mm

　（Ｆｉｇｕｒｅ　１）

right and left normally.

 Solution 1：Pull out the second cap manually when you hear the time report, then pull

Problem

FIXING BARS

You clock does not chime during the day.

out the minute hand in the same way and reinstall it to the 12 o'clock position, and

　１

ｐｉｃｔｕｒｅ

Solution

CABLE TIE

then manually rotate the minute hand clockwise to the 12 position to confirm whether

Reset the clock according to the "SETTING TIME AND CHIME" procedure.

REVISION 3: 07/12/2022

ATTENTION: ANTI TIPPING SAFEGUARD

CAUTION

BACK OF THE CLOCK

ASSEMBLY INSTRUCTIONS

COASTER FINE FURNITURE

TROUBLESHOOTING

SIZE D

2 PCS

ｈｏｌｅ

⑥

ｈｏｏｋ

Turn the minute hand(Longer hand)clock wise tenderly until the desired

③

ASSEMBLY TIME PER UNIT:

PARTS IDENTIFICATION

weight

①

FIGURE

Press the "time adj" button for adding the time of striking. For example,

WARNING

Injury may result from tipping furniture.

Do not allow children to climb on furmiture.

result in injury and damage.

HARDWARE IDENTIFICATION

FIGURE

BATTERY HOLDER

　（Ｆｉｇｕｒｅ　２）

STEP 7-2

STEP 4-2

STEP 1-2

ASSEMBLY TOOLS REQUIRED

①

④

The button in position( ): this selection will only

STEP 2-2

QTY

PART NAME

BACK PANEL

1PC

To turn button rightward or leftward to obtain the

1PC

BASE UNIT

DECORATION

CHAINS

1PC

PENDULUM

DECORATION

1PC

WEIGHTS

①

②

QTY

DESCRIPTION

LONG SCREW

8PCS

Grandfather Clock

2PCS

SHORT SCREW

　２

ｐｉｃｔｕｒｅ

PLASTIC ANCHOR

1PC

PAGE 10 OF 12

PAGE 11 OF 12

PAGE 12 OF 12

PAGE 5 OF 12

PAGE 2 OF 12

PAGE 3 OF 12

PAGE 4 OF 12

PAGE 6 OF 12

PAGE 7 OF 12

PAGE 8 OF 12

PAGE 9 OF 12

PAGE 1 OF 12

①

20 MINUTES

BY 2 PERSONS

①

FIGURE

①

ｔｕｒｎ　ｔｈｅ　ｌｏｎｇｅｒ

Fine Furniture for every stage of life

ｈａｎｄ　ｏｎｌｙ

FIGURE

900749

４５．

　（Ｆｉｇｕｒｅ　３）

　３

ｐｉｃｔｕｒｅ

COASTERFURNITURE.COM

QTY

1PC

4PCS

1PC

2PCS

QTY

1PC

　４

1PC