Euro-Pro Shark Retractor Transformer Vac 소유자 매뉴얼 - 페이지 8

{카테고리_이름} Euro-Pro Shark Retractor Transformer Vac에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Euro-Pro Shark Retractor Transformer Vac 17 페이지.

페이지 인쇄

Euro-Pro Shark Retractor Transformer Vac 소유자 매뉴얼

OPERATING INSTRUCTIONS

Emptying the Dust Cup Container

and Cleaning / Changing the Non-

Woven Pre-Filter, HEPA Filter &

Debris Screen

Warning:

Always unplug the

unit from electrical outlet before

opening the Dust Cup (container).

Important:

Do NOT use the vacuum

without the HEPA filter in place.

Warning

After each Use -

Always remove Filter Assembly

and the Dust Cup Cover with

the Debris Screen, then

vigorously "TapClean" HEPA

Filter and clean Debris Screen

and Non-Woven Pre-Filter until

no more dust can be removed.

IMPORTANT, Please Note: The

"TapClean" HEPA Filter will stop most of

the tiniest dust particles and airborne

allergens from re-entering the air you

breathe. In fact it stops 99.97% of all

particles as small as 0.3 microns - many

times smaller than a human hair!!!

Because of this incredible filtration

performance, the HEPA Filter will quickly

accumulate, inside the white filter folds,

many fine dust particles that are difficult to

see but which will eventually block or

reduce your suction power - if not cleaned

properly.

1. To remove the dust cup container,

first press on the dust cup release

button (1) that is located on the dust

cup handle and at the same time

press on the dust cup release button

(2) that is on the side of the upper

housing (Fig. 7). Then pull the dust

cup container out.

Dust

Release

Button 1

Dust

Cup

Release

Button 2

Fig. 7

2. To empty the dust

cup container,

press on the trap

door release button

that is on the back

side of the dust cup

container. (Fig. 8)

3. The HEPA filter is

located underneath the

dust cup container. (Fig.9)

Remove the Non-Woven Pre-Filter.

(Fig. 10) Remove the HEPA filter, hold

the edges and pull it out slowly.

Fig. 9

4. Hold the HEPA filter

by the edges and vigorously

"TapClean" the HEPA Filter

dirty side down on a hard,

flat surface until no more

dust is observed falling out

from between the pleats of

the filter. (Fig. 11) We

recommend washing the HEPA filter

once a month or when suction

appears to be reduced. Let the HEPA

filter air dry completely for 24 hours.

5. Rinse the non-woven pre-filter and let

air dry completely for 24 hours.

6. Insert the non-woven pre-filter.

7. Reinstall the HEPA filter in the

vacuum.

8. To separate the debris screen from

the dust cup, hold the dust cup in one

Cup

hand and turn the

dust cup cover counter

clockwise and pull apart.

To clean the debris

screen, we

recommend that you

rinse it under

lukewarm running

water to remove the dirt that

accumulates on it, but always allow it

to completely air dry before inserting

back into the vacuum. (Fig. 12)

IMPORTANT:

1. Ne pas utiliser l'aspirateur près des

chaufferettes, radiateurs ou mégots

de cigarette.

Fig. 8

Non-Woven

Pre-Filter

2. Avant d'insérer la fiche dans une

prise murale, assurez-vous que vos

mains sont bien sèches.

Fig. 10

HEPA

Filter

3. Avant de commencer le nettoyage,

assurez-vous d'enlever tout objet de

grande taille ou pointu risquant

d'endommager l'écran à débris de la

coupelle.

Fig. 11

Fig. 12

MESURES DE PRÉCAUTION

Si l'orifice de succion ou le boyau de l'aspirateur est BLOQUÉ,

arrêtez l'aspirateur et retirez l'obstruction avant de l'utiliser de

nouveau.

4. Pour débrancher la fiche de la prise

murale, tirez sur la fiche plutôt que

sur le cordon.

5. Évitez d'utiliser l'aspirateur pour

aspirer toute matière fumante ou

brûlante comme des cigarettes,

allumettes ou cendres chaudes.

6. Ne pas utiliser l'aspirateur sans que

TOUS les filtres sont en place.

Avertissement:

du cordon, gardez la fiche en main. Lors

du rembobinage, ne laissez pas

le cordon fouetter.

Lors du rembobinage