Euro-Pro S3325H 소유자 매뉴얼 - 페이지 4

{카테고리_이름} Euro-Pro S3325H에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Euro-Pro S3325H 8 페이지. Canister steam cleaner 120v., 60hz., 1500 watts

페이지 인쇄

ADDITIONAL IMPORTANT SAFEGUARDS cont.

1. To avoid circuit overload, do not operate another appliance on the same socket

(circuit)

2. If an extension cord is absolutely necessary, a 15 ampere 14 gage cord should

be used. Cords rated for less amperage may overheat. Care should be taken to

arrange cord so that it cannot be pulled or tripped over.

3. Do not leave unattended when the system is connected to a power

supply/electrical outlet.

SAVE THESE INSTRUCTIONS

FOR HOUSEHOLD USE ONLY

WARNING:

This appliance is equipped with a

grounded-type 3-wire cord (3-prong plug).

This plug will only fit into an electrical outlet

made for a 3-prong plug. This is a safety

feature. If the plug should fail to fit the

outlet, contact an electrician to replace the

outlet. Do not attempt to defeat the safety

purpose of the grounding pin, part of

the 3-prong plug.

CAUTION:

The force and heat of the steam may adversely

affect certain materials. Always check the

suitability of using the steam cleaner on a

surface by carrying out a preliminary test on a

hidden area.

Examples for guidance only: - Varnished wood or glossy leather can be

bleached by the effects of steam.

- Shiny plastic materials risk being

tarnished.

- Acrylic, velvets and linen are very

sensitive to the temperature of steam.

The manufacturer accepts no responsibility for damage caused to

objects, materials, animals or persons due to the inappropriate use of

steam, and through ignoring the advice and recommendations set down

in the Owner's Manual.

USAGE SUGGESTIONS FOR THE STEAM CLEANER

Window, Glass Surfaces & Mirrors

Use the window squeegee. Work with the

vapor jet on using the top to bottom

movements. Use the squeegee with the

vapor off to clear the water from the glass.

To do this without leaving streaks, use

lateral movements from the top to the

bottom of the surface.

Fiberglass or Stainless Steel

Surfaces

Use the floor brush or brass detail brush.

Slowly move the brush over the surface to

be cleaned. The vapor will emulsify the

dirt and grease on the surface. Follow

behind with a terry cloth towel over the

brush to remove excess moisture and

residue.

Tip: An old idea for polishing stainless

steel is to wipe it down with seltzer soda

water after it is cleaned.

Soap Scum

Soap scum dissolves almost immediately

under a combination of heat and

moisture. Rinse the surface with a small

amount of water afterwards or go back

over it once more with a clean terry cloth

towel.

Note: Soap scum sometimes will develop

a hard surface from waterborne minerals.

If this is the case, use the floor brush with

no towel first to break up this surface - or

spray or wipe first with lemon, vinegar or

seltzer soda water to soften the minerals.

Moving too slowly can dry out the soap

scum and cause it to granulate on the

surface. The surface will have a gritty

feel. If this happens, apply vapor to the

surface with the open brush again and re-

clean.

Blinds

Use the nylon detail brush to clean blinds.

Move the brush over the surface, allowing

enough time for the vapor to penetrate.

Work quickly on PVC blinds. Test for

color fastness on fabric blinds before

using. Finish by wiping with a towel.

Bathroom Areas

To clean the bathtub or shower area, use

the detail brush for grout, shower door

tracks, hard to get areas and heavily

soiled areas. The window squeegee will

be the most efficient way to clean the rest

of the area. Allow plenty of time for the

heat to penetrate the surface. This is

especially helpful in the shower area if

there is tile or grout. Wipe with towel.

Removal of soap scum on tile, grout, and

shower doors is also easier with the

steam cleaner

To clean sanitary fixtures, use the

concentrator nozzle with or without nylon

detail brush. Use a terry cloth towel or

paper towel to wipe up excess moisture

and residue.

To clean the sink and faucets, use nylon

detail brush then finish by wiping with a

towel.