Akurat lighting d2120 A1 매뉴얼 - 페이지 2
{카테고리_이름} Akurat lighting d2120 A1에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Akurat lighting d2120 A1 2 페이지. Universal on-camera led light
페이지 인쇄l Power supply
The A1 was designed to be powered from any of DC 6-18V/14W sources. The unit can easily be supplied from: (in example)
- camera socket via D-Tap connector (if the camera is equipped with a such slot)
- popular camcorder batteries (different brands), using DVB-02 adapter mounted to the lamp housing (optional)
- vehicles electrical systems (6 or 12V)
- AC power adapters
Check both, the voltage and the polarity, before connecting the light to the power source. Plus (+) of power source must be
connected to the middle pin of the A1 power socket, a minus (-) to the concentric outer electrode. The light is equipped with
a protection against damage as a result of attempts to supply the source of the reverse polarity, and in the case such
connection the unit just will not work.
Voltage greater then 20V may damage the light and consequently invalidate the warranty.
l Heat dissipation
In the case of long-term continuous operation, it must be ensure the free flow of air through the cooling fins to prevent overheating
of the lamp. Overheating of the device results the reduction of brightness, or, in extreme cases, turning off or damage the light.
Long term use of the light at full power at ambient temperatures exceeding 40 degrees Celsius or under conditions which prevent
the free flow of air through the cooling fins can cause damage to the lamp and void the warranty!
WARNING! Do not touch the heat sink after a long operation at full power. It can reach temperatures more than 60 degrees
Celsius.
The parts of device are surface protected from moisture. However, when using the light in the rain, protect it from flowing the water
under the cover.
It is unacceptable to immerse the light in the water!
l Warranty and Service
The warranty period lasts 12 months from the date of sale. The warranty includes free removal of defects revealed during the
operation under the conditions specified in this warranty card. To take advantage of the warranty, it is necessary that the following
conditions:
ţ
installation and operation of the equipment should be in accordance with this instruction
ţ
seal on the housing shall not be infringed
ţ
there aren't any corrections and amendments in the warranty card
WARRANTY DOES NOT COVER:
ý
damages caused by improper transportation or storage
ý
damages resulting from improper installation or operation, including mechanical damages
ý
damages resulting from handling inside the unit, construction changes, alterations and repairs to be carried out without the
consent of the manufacturer
In the case of defect covered by warranty, please contact your local dealer or send the unit at own expense to the manufacturer,
together with: this warranty card, description of damage, contact details, and the return address.
An employee of the manufacturer shall make an initial review of the device. The guarantor will contact with the person who
notified a defect, to take action to payable repair, in the case of detect described above events of the loss of the guarantees, or
detect of damages whom the warranty does not cover. The guarantor has the right to charge a fee for checking the equipment in
the amount of 15 € plus the cost of return shipping, if there is no agreement to payable repair or in the event of unjustified
complaints. In other cases, the defect will be removed free of charge, or equipment will be replaced. The new or repaired
equipment will be sent at the expense of guarantor for the applicant address within 14 days from the date of delivery for repair.
After the warranty expired, the guarantor will provide the payable after sales service, while stocks of spare parts for your model.
Contact details of the guarantor:
Akurat Lighting Sp. z o.o ul. Akurat 6 02-488 Warszawa
tel/fax +48 22 863 64 33 e-mail: [email protected]
date of sale
signature and stamp
Made in Poland