American Standard Champion 4 2002 설치 지침 매뉴얼 - 페이지 3

{카테고리_이름} American Standard Champion 4 2002에 대한 설치 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. American Standard Champion 4 2002 6 페이지. American standard two-piece toilet installation instructions

American Standard Champion 4 2002 설치 지침 매뉴얼
5
MANIFOLD INSIDE WATERWAY -
DO NOT REMOVE
6
BOLT CAP
WASHER
NUT
7
TANK MTG.
BOLTS PRE-
INSTALLED
WASHER/NUT
8
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
9a
Before continuing, determine the type of water supply connection you have from the chart below and use the appropriate assembly parts
required to properly reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
METAL/COPPER
FLARED TUBING
LOCK NUT
CONE
WASHER
COUPLING
NUT
WATER
SHUT-OFF
These parts must be used as
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in
water leakage. Water supply
tube or pipe must extend at
least 1/2" inside threaded
shank of valve (does not apply
to flanged tubing).
NUT
CLOSET
BOLT
FLANGE
CLOSET FLANGE
CLOSET BOLT
INSTALL TANK
a.
RUBBER
GASKET
b.
Recommended tool: Deep socket tool included in tank kit.
!
METAL FLANGED
METAL SPIRAL
TUBING
TUBING
LOCK NUT
EXISTING
WASHER
EXISTING
COUPLING
NUT
WATER
SHUT-OFF
Use existing
Use existing spiral
coupling nut
cone washer.
and washer.
Fluidmaster cone
washer may not
seal completely on
spiral type supply
line.
POSITION TOILET ON FLANGE
a.
Unplug floor waste opening and install toilet
on closet flange so bolts project through
TAPERED
mounting holes.
WASHER
b.
Loosely install retainer washers and nuts.
Side of washers marked "THIS SIDE UP"
must face up!
INSTALL TOILET
a.
Position toilet squarely to wall and, with a rocking motion,
press bowl down fully on wax ring and flange. Alternately
tighten nuts until toilet is firmly seated on floor.
b.
Install caps on washers.
(If necessary, cut bolt height to size before installing caps.)
c.
Smooth off the bead of sealant around base.
Remove excess sealant.
Install large rubber gasket over threaded outlet on bottom of tank and lower tank
onto bowl so that tapered end of gasket fits evenly into bowl water inlet opening,
and tank mounting bolts go through mounting holes. Secure with metal
washer/nuts.
With tank parallel to wall, alternately tighten hex nuts until tank is snugged down
evenly against bowl surface.
CAUTION:
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
DO NOT SPIN BOLTS WITH SCREWDRIVER
VINYL/BRAIDED
CONNECTOR
LOCK NUT
LOCK NUT
EXISTING
COUPLING
CONE
NUT
WASHER
COUPLING
NUT
WATER
WATER
SHUT-OFF
SHUT-OFF
Captive cone
washers already
included. No
additional washers
needed.
- 3 -
!
CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
7 30 5 29 -1 0 0 R e v. M