American Standard 2476 설치 지침 - 페이지 4

{카테고리_이름} American Standard 2476에 대한 설치 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. American Standard 2476 4 페이지. Dual flush 2-piece toilet
American Standard 2476에 대해서도 마찬가지입니다: 설치 지침 관리 및 유지보수 (13 페이지)

페이지 인쇄

LIFT ARM

FIRST

IMPORTANT: Always clear

sand and rust from system.

• Make sure water supply is

off. Remove valve TOP by

lifting arm and rotating top

and arm 1/8 turn

counterclockwise, pressing

down slightly on cap.

Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products. Fluidmaster shall

not be responsible or liable for any damages caused by products used with Fluidmaster valves that were

not manufactured by Fluidmaster, Inc.

PROBLEM

Does not flush

a. Water supply valve closed.

b. Supply line blocked.

c. Sand or debris lodged in water control.

Poor or sluggish flush

a. Bowl water level too low.

b. Supply valve partly closed.

c. Partially clogged trapway and/or drain pipe and/or vent.

d. Supply pressure too low.

Toilet leaks

a. Poor supply line connection.

b. Poor bowl to tank/floor connection.

Toilet does not shut off

a. Flush valve seat and/or rubber seal worn or deformed.

b. Sand or debris lodged in water control.

• While holding a container

• Replace TOP by engaging

over the uncapped VALVE

to prevent splashing, turn

water supply on and off a

few times. Leave water

supply off.

TROUBLESHOOTING GUIDE

POSSIBLE CAUSE

IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK

SLOWLY, repeat Step 13.

IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF

NON-USE, it is a signal you are wasting water because:

• The flush valve is leaking because it's worn, dirty or

IF FILL VALVE WON'T TURN ON OR SHUT OFF or REFILL OF

TANK WATER IS SLOW after valve has been in use for some

time, Fluidmaster Model 242 Replacement Seal may be needed.

Go to our website at www.fluidmaster.com for more solutions

to toilet problems.

For troubleshooting information please contact:

lugs and rotating 1/8 turn

clockwise. MAKE CERTAIN

TIP IS TURNED TO THE

LOCKED POSITION. VALVE

MAY NOT TURN ON IF TOP

IS NOT FULLY TURNED TO

THE LOCKED POSITION.

a. Open valve and allow water to fill tank.

b. Shut off water supply, disconnect supply line and inspect all gaskets and

washers. Reassemble. Also, see Fluidmaster maintenance. (see Step 14)

c. Shut off water supply. Remove cap and clean as per Step 14.

a. Check that water level is set to correct height in tank, also verify the flush

valve adjustments are set as per Step 10.

b. Open supply valve fully. Be sure that proper supply tube size is used.

c. Remove obstruction. Consult a plumber if necessary.

d. Normal supply pressure must be at least 20 psi.

a. Review Step 9 of installation procedure.

b. Review Step 4 through 7 of installation procedure.

a. Shut off water supply. Replace flush valve or flush valve silicone seal.

b. Shut off water supply. Remove cap and clean per Step 14.

- 4 -

TROUBLESHOOTING

misaligned with tank ball or flapper (replace with a new flapper).

30800 Rancho Viejo Road

San Juan Capistrano, CA 92675

(949) 728-2000 (800) 631-2011

www.fluidmaster.com

® Registered trademark of Fluidmaster, Inc.

CORRECTIVE ACTION

7 3 0 1 1 4 4 - 1 0 0 R e v. H