Da-Lite ACOUSTICAL IMAGER 지침서 - 페이지 7

{카테고리_이름} Da-Lite ACOUSTICAL IMAGER에 대한 지침서을 온라인으로 검색하거나 PDF를 다운로드하세요. Da-Lite ACOUSTICAL IMAGER 13 페이지.

페이지 인쇄

MOUNTING OPTIONS

3. Gently pull the slack out of the wire and screw the

adaptor onto the back of the speaker in two

places, as shown.

4. The floor stand adaptor screws may be found in

Hardware Bag B. Use the larger screw in the

upper screw hole, and the smaller screw in the

lower screw hole.

5. Screw the floor stand adaptor into the floor

stand's threaded insert until the speaker is firmly

attached to the stand. Back off slightly from the

fully-tightened position until the speaker is

oriented as desired, then rotate the thumbwheel

at the bottom of the floor stand adaptor to secure

the speaker to the stand.

WALL MOUNTING

NOTE: The customer is solely responsible for proper selection

of mounting hardware not included with the speakers, and for

proper assembly and installation of the wall-brackets,

including but not limited to the selection of the appropriate

weight-bearing supports and proper use of the bracket. Be

sure to follow these bracket assembly and installation

instructions carefully. If you have any questions or doubts

about your ability to correctly wall-mount the speakers,

consult with Da-Lite customer service.

1. Unscrew and remove the large molded nut. If

necessary, use the supplied Metal Bar as a lever

by inserting it into one of the holes in the outer

edge of the Molded Nut.

2. Firmly grasp the Ball and Shaft and pull it straight

out of the Attachment Plate. Avoid leaning it to

the side for leverage, as this may break off a tab.

ATTACHMENT

PLATE

#10 PAN-HEAD

WOOD SCREW

(NOT SUPPLIED)

4-PIECES

METAL BAR

BALL AND SHAFT

METAL NUT

MOLDED NUT

3. Slide the Molded Nut onto the Ball and Shaft with

the threaded opening facing the ball. Thread the

metal nut all the way onto the Ball and Shaft, with

the star washer side away from the ball. Refer to

the exploded drawing for the proper orientation of

these parts.

4. Screw the Ball and Shaft into the Threaded Insert

on the back of the Satellite Speaker until it is fully

seated in the Threaded Insert, but do not tighten as

you might dislodge the Threaded Insert. Such

damage would not be covered under the warranty.

5. Tighten the Metal Nut with the star washer side

between the Metal Nut and the back of the

Satellite Speaker, using large needle-nose pliers,

until it is firmly seated against the back of the

Speaker and has locked the Ball and Shaft and the

Satellite Speaker together. Note that once the

Metal Nut is fully tightened, it may embed some

marks on the back of the Satellite Speaker.

However, these marks will be covered by the

Metal Nut.

6. Mount the Attachment Plate into a wood stud on

the wall, using four #10 pan-head wood screws at

least one inch long (not supplied). Make sure that

all four screws are driven into the stud and not

into drywall.

NOTE: If the bracket needs to be mounted in drywall,

the customer is responsible for selecting and using

appropriate wall-anchors and screws.

METAL NUT

METAL BAR

NOTE: The Metal Nut must be fully tightened against the

Satellite Speaker as described in Step 5 before beginning

Step 8 in order to avoid damage to the Threaded Insert. Such

damage would not be covered under the warranty.

7. Connect the supplied speaker wires to the

surround speaker terminals, press the red or black

plastic cap for the desired terminal, insert the bare

end of the wire into the hole below the cap and

release the cap. Gently tug on the wire to make

sure that it is fully inserted.

SATELLITE SPEAKER

THREADED INSERT