Aston Global EMERALD EM1500 사용자 설명서 - 페이지 3
{카테고리_이름} Aston Global EMERALD EM1500에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Aston Global EMERALD EM1500 4 페이지.
페이지 인쇄Note：Once the battery is disconnected, the loads are not protected
from power outages.
1.
Use a cross-type screwdriver to remove five screws on bottom shell
and
screws on backplane.If there is a RS232 port,remove the
screws on the port please.
2.
Take off the top cover and front panel.
3.
1:Loosen the black wire from the negative (-) terminal and red wire
from the positive (+) terminal. 2:Remove the battery cover.
Should the UPS fail to function correctly we
recommend you perform the following tests
before calling the service.
Check step:
Step 1: Is the main switch in the "ON"
position?
Step 2: Is the UPS plugged into the mains
power supply?
Step 3: Does the power supply fall within
specified unit values?
Step 4: Has the fuse gone in the mains plug?
Step 5: Is the UPS overload?
Step 6: Is the battery flat or defective?
Model
Capacity
Input
Voltage
Voltage range
Output
Voltage Regulation
Transfer time
Waveform
Battery
Type & Number
Charging time
Physical
Dimension(DxWxH, mm)
Net Weight(kgs)
Packaging Dimension(DxWxH,
mm)
Gross Weight(kgs)
Environment
Humidity
Noise level
Safety
Security certificate
REPLACING THE BATTERY
4.
Exchange the new battery for the UPS
5.
1. Put on the battery cover on the battery. 2. Connect the battery leads to the new battery.
Note: Small sparks at the battery connectors are normal during connection.
6.
1:Install the top cover. 2:Install the front panel.
7.
Fasten the screws mentioned in step 1.
8.
Dispose of the old battery properly at an appropriate recycling facility.
TROUBLE SHOOTING
Situation
No LED display on the front
Low battery.
panel.
Battery fault.
The UPS is not turned on.
Alarm continuously sounds
The UPS is overload.
when the Utility is normal.
When power fails, back up
The UPS is overload.
time is shorten.
Battery voltage is too low.
Battery defect. It might be due to high
temperature operation environment, or improper
operation to battery.
The Utility is normal, but LED
Power cord is loose.
is flashing.
GRs 1000 / 1500 / 2000 SPECIFICATIONS
GRs 1000
1000VA / 700W
12V/7Ah x 2
9.3
10.3
Less than 40 dB
Check Items
Charge the UPS at least 6 hours.
Replace the battery with the same type of battery.
Press the power switch again to turn on the UPS.
Remove some loads first. Before reconnecting equipment, please
verify that the load matches the UPS capability specified in the specs.
Remove some critical load.
Charge the UPS at least6 hours.
Replace the battery with the same type of battery.
Reconnect the power cord properly.
GRs 1500
1500VA / 1050W
220/230/240VAC
165~290Vac
220/230/240VAC +/- 10%
Typical 6ms
Sine Wave
12V/9Ah x 2
4-6 hours recover to 90% capacity
393 x 165 x 198
12.4
450 x 238 x 301
13.4
0-90 % RH @ 0-40 C (non-condensing)
CE
Solution
GRs 2000
2000VA / 1400W
12V/9Ah x 2
12.6
13.6
Less than 45 dB