Aston Global EMERALD EM2000 사용자 설명서 - 페이지 3

{카테고리_이름} Aston Global EMERALD EM2000에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Aston Global EMERALD EM2000 4 페이지.

페이지 인쇄

Note：Once the battery is disconnected, the loads are not protected

from power outages.

Use a cross-type screwdriver to remove five screws on bottom shell

and

screws on backplane.If there is a RS232 port,remove the

screws on the port please.

Take off the top cover and front panel.

1:Loosen the black wire from the negative (-) terminal and red wire

from the positive (+) terminal. 2:Remove the battery cover.

Should the UPS fail to function correctly we

recommend you perform the following tests

before calling the service.

Check step:

Step 1: Is the main switch in the "ON"

position?

Step 2: Is the UPS plugged into the mains

power supply?

Step 3: Does the power supply fall within

specified unit values?

Step 4: Has the fuse gone in the mains plug?

Step 5: Is the UPS overload?

Step 6: Is the battery flat or defective?

Model

Capacity

Input

Voltage

Voltage range

Output

Voltage Regulation

Transfer time

Waveform

Battery

Type & Number

Charging time

Physical

Dimension(DxWxH, mm)

Net Weight(kgs)

Packaging Dimension(DxWxH,

mm)

Gross Weight(kgs)

Environment

Humidity

Noise level

Safety

Security certificate

REPLACING THE BATTERY

Exchange the new battery for the UPS

1. Put on the battery cover on the battery. 2. Connect the battery leads to the new battery.

Note: Small sparks at the battery connectors are normal during connection.

1:Install the top cover. 2:Install the front panel.

Fasten the screws mentioned in step 1.

Dispose of the old battery properly at an appropriate recycling facility.

TROUBLE SHOOTING

Situation

No LED display on the front

Low battery.

panel.

Battery fault.

The UPS is not turned on.

Alarm continuously sounds

The UPS is overload.

when the Utility is normal.

When power fails, back up

The UPS is overload.

time is shorten.

Battery voltage is too low.

Battery defect. It might be due to high

temperature operation environment, or improper

operation to battery.

The Utility is normal, but LED

Power cord is loose.

is flashing.

GRs 1000 / 1500 / 2000 SPECIFICATIONS

GRs 1000

1000VA / 700W

12V/7Ah x 2

9.3

10.3

Less than 40 dB

Check Items

Charge the UPS at least 6 hours.

Replace the battery with the same type of battery.

Press the power switch again to turn on the UPS.

Remove some loads first. Before reconnecting equipment, please

verify that the load matches the UPS capability specified in the specs.

Remove some critical load.

Charge the UPS at least6 hours.

Replace the battery with the same type of battery.

Reconnect the power cord properly.

GRs 1500

1500VA / 1050W

220/230/240VAC

165~290Vac

220/230/240VAC +/- 10%

Typical 6ms

Sine Wave

12V/9Ah x 2

4-6 hours recover to 90% capacity

393 x 165 x 198

12.4

450 x 238 x 301

13.4

0-90 % RH @ 0-40 C (non-condensing)

Solution

GRs 2000

2000VA / 1400W

12V/9Ah x 2

12.6

13.6

Less than 45 dB