DoorHan FAST-750 설치 및 운영 매뉴얼 - 페이지 10
{카테고리_이름} DoorHan FAST-750에 대한 설치 및 운영 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. DoorHan FAST-750 16 페이지.
DoorHan FAST-750에 대해서도 마찬가지입니다: 설치 및 운영 매뉴얼 (18 페이지)
페이지 인쇄
1
PrograMMIng
PROGRAMMING
Preparation
put the slide in locked state.
turn on the power supply, an indicator on the operator will light up
and a sound signal will be heard.
If the programming is not completed, the settings will not be saved.
If there is a mistake in any of the settings, you can turn off the power
and restart programming.
to get access to the programming panel, remove the protective
cover by the face panel of the operator.
Upper Limit Setting
R
+
P
�
Press key "p"
The unit beeps once
(about 5 seconds)
Down Limit Setting
R
+
P
�
Operating Force Learning
R
+
P
�
Press "p", "3" flashes
Press "�", shows "3"
After the above basic settings, the user can now carry out the finalizing step to finalize the programming
Force Level Setting
The unit has been preset on the factory at level 4,resetting by end users is not required.
S
+
P
�
Press "�" to show "4"
If the force level is set too low, the door moving
will be affected when the mechanical
structure of the door is not well�balanced
Transmitter Control Button Settings
R
+
10
I n s t a l l a t I o n a n d o p e r a t I n g m a n u a l s e C t I o n a l - 7 5 0 / 1 2 0 0
P
�
Press "p", "2" flashes, it
Press "�" to show "5"
means now the door
R
R
+
P
P
�
Press "p", "1" flashes
and shows "1"
R
+
R
P
�
P
Press "�" to show "2"
Press "p" ,"2" flashes
R
+
P
�
Door rises automatically
S
+
R
P
�
P
Press
Press "p"
R
P
R
R
+
P
�
P
Press "+" or "�",to choose
a desired button from 1 to 4
1.
radio code store key – «r»
2.
setting selection keys – «+», «-»
3.
programming key – «Р»
4.
Indicator of receiver signal coding key
5.
Indicator of operator work and programming
6.
light lamp
+
R
+
�
P
�
Press "+"
Or press "�"
+
R
+
�
P
�
Press "�"
Or press "+"
R
+
P
�
Press "p" after stops,
press "p" again
3 sec
+
press "+" or "�" for changing force level
�
Manual adjustment (max force level 60 kg)
Low
3 sec
+
press "+" or "�" for changing force level
�
Automatic adjustment (max force level 20 kg)
Set in the factory
+
�
The motor has been set at channel 2 at the factory
R
P
When the door rises to
Door goes up
an ideal position, press
key "P" to save
the Information
R
P
When the door descends
Door goes down
toan ideal position,
after 2 seconds press key
"P" to save the information
R
P
Press "P" to save the
Door descends
information, refer to
Set in the factory
Force level
Press to "p" to save the settings
+
�
+
�
+
�
High