Canon PIXMA MP610 Series 서비스 매뉴얼 - 페이지 12
{카테고리_이름} Canon PIXMA MP610 Series에 대한 서비스 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Canon PIXMA MP610 Series 45 페이지. All-in-one photo inkjet printer
Canon PIXMA MP610 Series에 대해서도 마찬가지입니다: 여기에서 시작 (2 페이지), 보충 설명서 (6 페이지), 브로셔 및 사양 (2 페이지), 빠른 시작 매뉴얼 (40 페이지), 빠른 시작 매뉴얼 (2 페이지)
페이지 인쇄
- 1. Table of Contents
- 1. 1 Maintenance
- 1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consumables by Service Engineer
- 1. Customer Maintenance
- 1. Special Tools
- 1. Serial Number Location
- 2. 2 List of Error Display / Indication
- 2. Operator Call Errors
- 2. Service Call Errors
- 2. Other Error Messages
- 2. Warnings
- 2. Troubleshooting by Symptom
- 3. 3 Repair
- 3. Notes on Service Part Replacement
- 3. Adjustment / Settings
- 3. Verification Items
Unsatisfactory print quality No printing, or no color ejected.
Carriage movement problems (contact
to other parts, strange noise).
Faulty scanning (no scanning, strange
noise).
The CD / DVD tray is not pulled in the
feeder.
Printing is faint, or white lines appear on
printouts even after print head cleaning.
Line(s) not included in the print data
appears on printouts.
Paper gets smeared.
The back side of paper gets smeared.
- Set the paper properly.
- Confirm the following:
- selected paper source
- attachment of the rear cover
- connection of each harness and the logic board
- sheet feeder unit operation
- Replace the
- sheet feeder unit,
- cassette unit, or
- logic board.
- Confirm that the carriage timing slit strip film is free from
damage or grease.
- Clean the carriage timing slit strip film (with ethanol and
lint-free paper).
- Remove foreign material.
- Replace the
- carriage timing slit strip film, or
- carriage unit.
- Confirm the connection between the scanning unit and the
logic board.
- Replace the
- scanning unit, or
- logic board.
- Confirm that the reflector of the CD / DVD tray is clean
and is free from any damages.
- Replace the
- CD / DVD tray, or
- logic board.
- Confirm that the orange tape is properly removed from an
ink tank, and the ink tanks are installed properly.
- Perform print head maintenance.
- Replace the
- ink tank,
*1
- print head
.
- Remove foreign material from the purge unit caps, if any.
- Replace the
- purge unit, or
- logic board.
- Remove and re-install the print head.
- Confirm that the ink tanks are installed properly.
- Perform print head maintenance.
- Replace the
- ink tank, or
*1
- print head
.
- Perform the following:
- Automatic or manual print head alignment in the user
mode
- LF / Eject correction in the service mode
- Clean the paper feed rollers.
- Replace the
- purge unit, or
- logic board.
- Feed several sheets of paper.
- Perform bottom plate cleaning.
- Clean the paper path with a cotton swab or cloth.
- Clean the paper feed rollers.
- Clean the platen rib (clean the paper path with a cotton
swab or cloth).
- Confirm that the platen ink absorber fits in place properly.
- Confirm that the paper eject rollers are free from ink
smear.
10 / 43