Canon PIXMA MP760 사용자 설명서

{카테고리_이름} Canon PIXMA MP760에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Canon PIXMA MP760 2 페이지. Photo all-in-one printer
Canon PIXMA MP760에 대해서도 마찬가지입니다: 보충 설명서 (6 페이지), 빠른 시작 매뉴얼 (41 페이지)

페이지 인쇄

READ THIS SHEET FIRST

Thank you for purchasing the Canon PIXMA MP760. To prepare your machine for use, please follow these

Easy Setup Instructions before referring to any other documentation.

IMPORTANT

Do not connect the USB cable until after the software is installed. See the rear side of this sheet for details.

Unpack and install the machine.

Check the package contents.

• Machine

MP760

• Ink tanks

Black

BCI-3eBK

• Easy Setup Instructions • Quick Start Guide

• Setup CD-ROM (Windows: silver, Macintosh: white)

The Setup CD-ROM contains the MP Drivers, as well as the User's Guide, Software Guide and Photo

Application Guide in electronic format. Please read these guides.

A printer cable is not included. You must purchase a USB cable (less than 10 ft./3 m) to connect your

machine to a computer.

Connect the power cord.

1. Connect one end of the power cord to the rear of the machine.

2. Connect the other end to the AC outlet.

If the message <There is no print head installed. Install the print head.>

appears, go to Step 4, "Install the print head."

Load the paper.

Open the Paper Support, then pull out the extension.

Load a few sheets of letter-size blank paper into the Auto Sheet Feeder.

(1) Open the Paper

Support.

(2) Pull out the extension

until it stops.

Install the print head.

Ensure that the Paper Output Tray is

open. Then lift the Scanning Unit

(Printer Cover) until it locks into place.

IMPORTANT

Be sure to hold the Scanning Unit firmly with one

hand.

Remove shipping tape from the

Inner Cover and Open Both Inner

Covers.

The Print Head Holder moves to the center.

Do not touch the Print Head Holder while it is

moving.

Inner Covers

Start Here

Easy Setup Instructions

• Power cord

• Print head

Black

BCI-6BK

Cyan

BCI-6C

Magenta BCI-6M

Yellow

BCI-6Y

Load the paper with the print side face up.

Pinch and adjust

the paper guide

to the width of

the stack.

Ensure the paper stack

does not exceed the paper

limit mark.

(1) If the Paper Output

Tray is not open,

press the Open

(3) Lift the

Button.

Scanning

Unit.

Click

(2) Pull

the

Scanning

Unit

Lever.

Raise the lock lever.

Touch only the lock lever!

Raise lock lever

completely.

Prepare the print head.

Do not touch!

Remove the protective cap and discard it.

Lower the lock lever.

Install the ink tanks.

Prepare the ink tanks.

Remove the orange-colored

protective film. If it is not

removed completely,

problems with printing

may occur.

Insert the ink tanks.

Click

Press down until the ink

tank clicks into place.

Close the Inner Covers and the Scanning Unit (Printer Cover).

Click

Close the two Inner Covers.

Align the print head from the Operation Panel.

Be sure to align the print head to ensure print quality.

Press [OK] to start print head alignment.

(1) This message appears.

(2) Press [ ] to select <Yes>.

If this message

does not appear

after closing the

Scanning Unit,

see "Aligning

The Print Head

Automatically"

in the Quick Start

Guide.

If the printed pattern matches the illustration, print head alignment is complete.

You can change the language displayed on the LCD.

For details, see "Selecting The Language For The LCD" in the Quick Start Guide.

Hardware setup and print head alignment is complete.

If you are connecting the machine to a computer for use, see the rear side of this sheet for

instructions on installing the software.

Canon and BCI are registered trademarks and PIXMA is a trademark of Canon Inc. in the United

States and may also be registered trademarks or trademarks in other countries.

All other products and brand names are registered trademarks or trademarks of their respective owners.

Specifications subject to change without notice.

HT7-0228-000-V.1.0

Insert the print head.

(2) Push back.

(1) Insert.

Do not touch!

Click

Lower the lock lever

until you hear a click

as it locks into place.

Remove the protective cap

and discard it.

Do not touch!

Good example

Bad example. Tank 6Bk is

not fully inserted. Make

sure to press it down until

you hear a click.

Click

Pull the Scanning Unit Lever

towards you to close the

Scanning Unit.

IMPORTANT

Be sure to hold the Scanning Unit firmly with one hand.

(4) The machine will print

the print head position

pattern and automatically

align the print head.

(3) Press [OK].

PRINTED IN CHINA