Canon PIXMA MP800 여기에서 시작

{카테고리_이름} Canon PIXMA MP800에 대한 여기에서 시작을 온라인으로 검색하거나 PDF를 다운로드하세요. Canon PIXMA MP800 2 페이지. Personal printing guide
Canon PIXMA MP800에 대해서도 마찬가지입니다: 브로셔 및 사양 (4 페이지), 보충 설명서 (6 페이지)

페이지 인쇄

Unpack the machine

Please confirm bundled thing by the illustration printed on the flapped lid of the packing box.

Turn on the machine.

Unlock the Scanning Unit.

(1) Open the Document Cover.

(2) Move the Scanner Lock Switch towards

the release mark to unlock the Scanning

Unit.

CAUTION

• Make sure to unlock the Scanning Unit before

turning the machine on.

• Before transporting the machine, always lock

the Scanning Unit by moving the Scanner

Lock Switch towards the lock mark.

Connect the power cord, then press [ON/OFF].

(2) Connect the other end to the AC outlet.

Use [

] or [

] on the Operation Panel to select the language for the LCD,

then press [OK].

The language setting is only available for some countries.

If the message <Install the print head and set the ink tank.> appears, go to Step

2, "Install the Print Head."

Install the Print Head.

Lift the Scanning Unit (Printer Cover) until it locks into place.

Lift the Scanning Unit

(Printer Cover).

IMPORTANT

For safety, always firmly grip the areas illustrated when opening the Scanning Unit (Printer

Cover).

Pull out the Paper Output Tray extension.

If the Paper

Output Tray does

not open, press

the Open Button.

Open the Inner Cover.

The Print Head Holder moves to the center.

Do not touch the Print Head Holder while it is

moving.

Serial Number

Inner Cover

Location

IMPORTANT (US Only)

Write down the serial number located inside

the machine. You will need this to register

your products.

Prepare the Print Head.

(1) Remove the print head from its package.

CAUTION

There might be some transparent or light blue

ink on the inside of the bag the print head

comes in - this has no effect on print quality. Be

careful not to get ink on yourself when

handling these items.

Start Here

Easy Setup Instructions

release mark

(3) Press [ON/OFF].

(1) Connect one end of the power cord

to the rear of the machine.

(2) Press

[OK].

(1) Press [ ] or [ ] to

select the language.

When the machine is

turned on, lift up the

Scanning Unit (Printer

Cover) then wait for the

Paper Output Tray to

open.

Pull out the Paper

Output Tray extension.

Raise the lock lever.

Touch only the

lock lever!

Raise lock lever

completely.

IMPORTANT

If the Scanning Unit (Printer Cover) is left

open for more than 10 minutes, the Print Head

Holder moves to the right. Close and reopen

the Scanning Unit (Printer Cover) to return

the Holder to the center.

(2) Remove the protective cap and discard it.

Do not touch!

Remove the protective cap and discard it.

CAUTION

There might be some transparent or light blue

ink on the inside of the protective cap - this has

no effect on print quality. Be careful not to get

ink on yourself when handling these items.

Insert the Print Head.

Do not touch!

Insert.

Install the ink tanks.

Prepare the ink tanks.

(1) Peel back the orange

tab completely and

remove the plastic

wrapper from the ink

tank.

If the orange-colored protective film is

not removed completely, problems with

printing may occur.

Insert the ink tanks.

(1) Insert the ink tank into the

rightmost slot.

Close the Inner Cover and the Scanning Unit (Printer Cover).

Click

Close the Inner Cover.

Align the Print Head from the Operation Panel.

This procedure is necessary to obtain a beautiful print result.

The Print Head positions is automatically aligned.

When the pattern shown on step 3-(3) is printed, the alignment is completed.

Be sure to align the Print Head to ensure print quality.

Open the Paper Support, then pull out the extension.

(1) Open the Paper

Support.

Load a few sheets of letter- or A4-size blank paper into the Auto Sheet Feeder.

(2) Pinch and adjust the

paper guide to the

width of the stack.

Ensure the paper stack does not

exceed the paper limit mark.

Press [OK] to start Print Head alignment.

(1) This message appears.

If this message does

not appear after

closing the Scanning

Unit (Printer Cover),

see "Aligning The

Print Head

automatically" in the

User's Guide.

• Print head alignment will take several minutes to complete. Do not start another operation here.

• If the printed pattern matches the illustration, Print Head alignment is complete.

You can change the language displayed on the LCD.

For details, see "Selecting the Language for the LCD" in the Quick Start Guide.

Hardware setup and Print Head alignment is complete.

If you are connecting the machine to a computer for use, see the rear side of this sheet for

instructions on installing the software.

"Windows" is a trademark of Microsoft Corporation, registered in the United States and other countries.

"Macintosh" and "Mac" are trademarks of Apple Computer, Inc., registered in the U.S. and other countries.

Specifications are subject to change without notice.

xx2005A

Lower the lock lever.

Lower the lock

lever carefully

and press it

down.

(2) Twist off and discard

the orange protective

cap located on the

bottom of the ink

tank.

Do not press!

IMPORTANT

Do not touch the

electrical contacts

electrical contacts.

(2) Press the

mark on the ink tank until it clicks into place

and then its lamp lights red.

Refer to the color guide on

Click

the print head lock lever.

IMPORTANT

For safety, always firmly grip the areas illustrated when

closing the Scanning Unit (Printer Cover).

(2) Pull out the

extension until

it stops.

(3) Pinch and slide

the paper guide

to the left end.

(1) Load the paper with

the print side face up.

Align the paper with

the cover guide, then

slide the paper guide

toward the left edge of

the paper.

(2) Make sure <Yes> is selected,

(3) The machine will

then press [OK].

print the Print Head

position pattern and

automatically align

the Print Head.

The pattern is

printed in black and

blue.

PRINTED IN THAILAND

QT5-0033-V01