dacell SM150 매뉴얼 - 페이지 3
{카테고리_이름} dacell SM150에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. dacell SM150 4 페이지. Digital indicator
dacell SM150에 대해서도 마찬가지입니다: 사용 설명서 (12 페이지)
페이지 인쇄5. HARDWARE
1) Selection of AC input power
(1) Separate P.C.B from case.
(2) The following label is existed under power transformer
110 220 110
2) Transformation of SAMPLING TIME
15 times/sec (standard).
(1) The following label is existed on the P.C.B
○
○
○
15
C
30
3) Setting of DIP switch
After connection, dip s/w must be set.
ON
1
2
3
1
1.5
2
mV/V
mV/V
mV/V
One of 1,2,3 or
4
turn
on
according
to
sensor
output
value (mV/V)
6. SOFTWARE
1) CALIBRATION DATA
Set data as follows according to sensor output value.
Confirm calibration data after auto calibration execution.
1 mV/V range
---
1.5 mV/V range
--- 1.250
2 mV/V range
--- 1.750
3 mV/V range
--- 2.500
2) Adjustment of display time and measurement data unit
(1) Press mode key, FS DP LED turn on at the same time.
(2) 01.01 is displayed.
(3) Display time (set 1 times : fastest, set 15 times : slowest)
0 1 . 0 1
Setting of displat time
01 - After 1 times sampling, display
02 - After 2 times
:
:
:
:
14 - After 14 times
15 - After 15 times
3) PROGRAM (SOFTWARE) OPTION
(1) Press mode key, DP CAL LED turn on at the same time.
mode
display
peak hold on : display maximum
peak hold off : display present
0 x x x
reset : stored maximum measurement
Adjustment
of peak
peak hold on(only) : display and reform
hold mode
peak hold off : stored maximum
1 x x x
110V : connect 1 and 2
connect 3 and 4
220V : connect 2 and 3
15 times/sec : connect 1 and C
30 times/sec : connect 2 and C
4
5
6
7
voltage
3
1Hz 10Hz 100Hz
mV/V
current
analog input
Turn
on
filter
or off
frequency
according
6,7,8
to analog
off : 4㎑
output
0.700
～
1.249 mV/V
～
1.749 mV/V
～
2.499 mV/V
～
3.500 mV/V
＋
Setting of adjustment width
01 : display 1, 2,
......
"
02 : display 2, 4, 6, 8,
0(even)
05 : display 5, 10, 15
"
10 : display 10.....90
"
20 : display 20, 40, 60, ...
50 : display 50, 00
＋
description
measurement data
measurement data..
data is removed.
maximum measurement data
measurement data is removed
automatically.
mode
Parity of
Display
Tracking
mode of
zero point
Average
value
display of
8
Signal
7. ALARM OUTPUT (RELAY OUTPUT)
High and low relay are a and b contact respectively.
Contact capacity is maximum AC 250V/5A and DC 30V/5A.
Relay contact operating time is maximum (1/Sampling Time) mm
Sec
* Output of transistor NPN open collector is option.
turn
mode
HIGH
RELAY
LOW
RELAY
8. TECHNICAL DATA
allowed time temperature
operating temperature
power of sensor
input signal type
max. load current
frequency response
analog output
relay output
relay response
nonlinear characteristics
, 9
temperature coefficient
display size
sampling time
filter frequency
short protection circuit
max. display range
weight
power
9. Unit Label change
* Unit label is optional.
* In the case of exchanging label, refer to as follows
1, Separate P.C.B from the case.
2, Remove Conventional unit label and then adhere new
label.
3, Put together indicator in reverse process.
display
description
standard type.
x 0 x x
ex)
＋
20mA : display 1000.0
display ( ) to ( )
＋
signal and display indicate opposite.
x 1 x x
ex)
＋
20mA : display -760.0
standard type.
x x 0 x
Display 0 : trace minute signal to 0
Display 0 : display minute signal.
x x 1 x
Use in case of leakage measurement.
display measurement signal immediately.
x x x 0
display average value of measurement
signal (7 times sampling).
x x x 1
setting
high data > setting value
high data
≤
setting value
low data
≤
setting value
low data > setting value
item
―
40
5Vdc or 10Vdc
10Vdc/60 , 5Vdc/120
0 10V,0 20 ,1 5V, 4 20
～
～
220V/5A (a,b contact)
Max 66 /sec
±0.02 /F.S
±0.02 F.S/
15 times/sec, 30 times/sec
1 , 10 , 100 , 4
㎐
protection circuit (insert)
-19999
size
w 96 ×h 48 ×d 126
㎜
110Vac, 220Vac (50 60 )
－
relay
ON
OFF
ON
OFF
data
℃ ～
80
℃
0
℃ ～
50
℃
1
～
3mV/V
㎃
㎃
Max 5㎑
㎃ ～
～
㎃
㎜
％
％
℃
14 ×8
㎜
㎜
㎐
㎐
㎑
～
19999
㎜
㎜
650g
～
㎐