AmerTac OMLC3BC 지침

{카테고리_이름} AmerTac OMLC3BC에 대한 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. AmerTac OMLC3BC 2 페이지. Motion activated light control

Motion Activated

Light Control Instructions

This light control automatically turns a light on when motion is detected and off 10 minutes after the motion stops. It senses activity

at distances up to 30 feet away. Never come home to a dark house again.

Damp Locations Only – Not for Wet Location Use – Suitable for fixtures from 8 feet to 18 feet high.

Caution: This motion sensor is not designed for use with an enclosed or shaded fixture of any kind. Infrared cannot penetrate glass

or plastic. Works with any compact fluorescent, halogen or incandescent bulb 150 watts max.

DIRECTIONS FOR USE:

• Turn power to light socket off.

• Remove the light bulb from socket.

• Screw the Motion Activated Light Control into the empty socket until snug.

• Screw the light bulb into the Motion Activated Light Control.

• For best performance, the sensor window should orient below the bulb. (See Fig. 1) If it is

not, rotate the Motion Activated Light Control counterclockwise until the sensor window

is between the 3 o'clock and 9 o'clock positions. This is achieved by unscrewing the

Motion Activated Light Control until the sensor is in the optimal position. The spring

loaded pin at the base of threads will maintain electrical contact with the fixture up to

270° (3/4 of one full turn) from it's fully seated position.

• The motion sensor can be tilted up or down (up to 20° in either direction) and rotated left

or right (up to 90° in either direction) to accomodate your unique installation. (See Fig. 1)

Note: Be sure to position the Sensor Window so that it can "see" past the bulb or any

other object that may block the Sensor's view. (See Fig. 2)

Caution: Do not adjust motion sensor after adapter is installed into socket.

• Turn the power on. If it is dark, the light will turn on. The light will turn off 10 minutes

after you leave the area. If it is daytime, the light will not activate until it becomes dark.

• The unit will now automatically turn the light on when motion is sensed and off 10

minutes later.

Note: This unit has a sensor to prevent lights from being turned on during daylight hours.

Other lights in the field of view may interfere with proper operation of the sensor at night.

To remedy, reposition sensor window away from other light sources, and in dual light

fixtures, position sensors so that they face away from light shone from adjacent bulb. (See

Fig. 3)

ONE YEAR LIMITED WARRANTY: AmerTac™ warrants this product to be free from defects in

material and workmanship for a period of 1 year from the date of purchase (does not include bulb).

AmerTac's obligations are limited to repairing or replacing any defective units and are effective only

if such units are returned with sales receipt within five years of the purchase date to AmerTac, 250

Boulder Drive, Breinigsville, PA 18031. Warranty void if damage is due to misuse or improper

installation. In no circumstance will AmerTac be liable for consequential or incidental damages

relating in any way to this product.

Questions, ¿Preguntas?, Questions? 1-800-777-0802

250 Boulder Drive

Breinigsville, PA 18031

www.amertac.com

Made in China / Hecho en China / Fabriqué en Chine

I09-0001-D

OMLC3BC, OMLC3BCCAN

MOTION SENSOR

SENSOR DE MOVIMIENTO

CAPTEUR DE MOUVEMENT

SENSOR WINDOW

VENTANA SENSORA

FENÊTRE DU CAPTEUR

WRONG

INCORRECTO

INCORRECT

120~V, 60HZ, 150 Watts Max

BULB

FOCO

AMPOULE

FIG. 1

WRONG

FIG. 2

FIG. 3