Flycolor 4in1-20A 사용자 설명서

{카테고리_이름} Flycolor 4in1-20A에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Flycolor 4in1-20A 2 페이지. Multi-rotor brushless esc

Thank you for purchasing our brushless electronic speed controller (ESC) . Any Improper operationmay cause personal injury damage

to the product and related equipments. This high power systemfor RC model can be dangerous ,we strongly recommend reading the

user manual carefully and completely. We will not assume any responsibility for any losses caused by unauthorized modiﬁcations

to our product. We have the right to change the design, appearance, performance and usage requirements of the product without

ATTENTION

notice.

Main features

1.Highly integrated Power Supply Board / ESC / Flight Control, All of them can be separately removed for maintenance, upgrade

faster and more convenient. light weight, good performance.

2.Plug type F3 ﬂight control, anti plug, convenient and fast for installation. Flight control with a buzzer for Alarm.

3.Dedicated drive IC, faster response, smaller and lighter.

4.Power supply board integrated 12V/1A ,5V/3A and battery voltage (BATV) power supply, could supply different voltages for

Camera, AV transmitter and LEDs.

5.No signal cable, maximum extent reduces the crosstalk caused by signal transmission, and makes ﬂight more stable.

6.No power supply wire for ﬂight control , no voltage detection wire and Alarm cable, make the overall weight lighter, install

faster, more convenient.

ESC

compatible with "regular" signal-receiving mode and "Oneshot125"signal-receiving mode (throttle signals range from

125μs～250μs).

8.Use BLHeli open-source ﬁrmware, can update the ﬁrmware or write setup via signal cable; Using "Damped light" mode , it

improves the throttle response, when reducing the throttle amount, the Motors slow down rapidly. It strengthens the stability

and ﬂexibility of multi-rotors, quite suitable for QAVs.

Speciﬁcation

Model

Manufacture Model

4in1-20A

S-FW020004-D

4in1-30A

Par t list / Dimensions

Description

Item

四合一电调

4in1 ESC

飞控

Flight control

尼龙支撑柱 M3*6+6

Nylon spacer M3*6+6

尼龙螺母 M3

Nylon Nut M3

尼龙螺钉 M3*10

Nylon screw M3*10

屏蔽线

Shield cable

*All pictures are for reference only

Wiring diagram

Please ensure all solder joints are insulated with heat shrink where necessary.

-（GND）

BATV

-（GND）

+5V

GND

BATV

Battery Voltage

GND

+5V

Connect to the Camera or

AV transmitter single cable

The anti-interference ability of some camera and AV transmitter

is not strong, easily affected by external interference. In

order to improve the anti-interference ability, we will

provide a shield cable additional, you could:

1.Directly connect with the connecting line between the

camera and the AV transmitter.

ATTENTION

2.If you chose the join points "S"for camera and AV

transmitter, you can connect the shield cable to the join

points on the PCB, see the ﬁgure right side.

(Please check to ensure no shor t circuit after welding )

User Manual

Multi-Rotor Brushless ESC

4 i n 1

BLHeli

Burst Current

Con. Current

(10S)

20A

30A

40A

Qty.

V+

V -

BEC

LiPo cells

5V/3A,12V/1A

2-4S

5V/3A,12V/1A

2-4S

V +

Battery+

V -

Battery-

Motor A

Motor B

Motor C

- (GND)

BATV

Sprial shield connect GND " "

- (GND)

+5V

Conductor connect "S"

Weight

Size

47.2g

102x43x15mm

47.2g

102x43x15mm

安装尺寸 Installation dimension

102

30±0.5

12V

BATV

-（GND）

+5V

12V

BATV

Battery Voltage

GND

+5V

Connect to the Camera or

AV transmitter single cable

Sprial shield connect GND " "

Conductor connect "S"

*All pictures are for reference only

Typical Applications

(For reference)

210-330 Multi

210-450 Multi

12V

BATV

-（GND）

+5V