Flycolor A-CW035003 사용자 설명서 - 페이지 2

{카테고리_이름} Flycolor A-CW035003에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Flycolor A-CW035003 2 페이지. Brushless car esc

페이지 인쇄

Programming

Programming with set button in the switch.

Note:

●

Motor will emit "BEEP" when indicator light ﬂashes.

●

When N>=5, indicator light will ﬂash for a long time ( with long tone ) to represent 5 .For example, ESC red indicator ﬂashes for a long time

once ( motor emits long tone "BEEP---" at the same time) , shows that enter the 5th set option. If ESC green indicator ﬂashes for a long time

once then for a short time once ( motor emits long " BEEP---" once and short "BEEP" once at the same time), shows that it enters the 6th set

option. And the like, the 7th set option "BEEP---BEEP,BEEP,BEEP", the 8th set option " BEEP---BEEP,BEEP,BEEP".

Turn off ESC power switch

Press"Set" button and

turn on power supply

and turn on transmitter

power switch.

switch

Release

button

Green LED

Enter the 1st set option -

ﬂashed once

"Running Mode".

Press button for 3 seconds

Release

button

Green LED

Enter the 2nd set option -

ﬂashed twice

"Fixed Area Accelerator".

Press button for 3 seconds

Release

button

Green LED

Enter the 3rd set option -

ﬂashed 3 times

"Initial brake force"

Press button for 3 seconds

......The following procedure is as above

Press button

Press button for 3 seconds

for 3 seconds

Release

button

Green LED

Enter the No."N" set option

ﬂashed "N" times

Green LED ﬂashes "N"

Red LED ﬂashed and

times, it shows battery

continuously press

cells number.

"Set"button.

Red LED ﬂashes once, select

"Forward with brake"

Press "Set" button once,

select next option.

Red LED ﬂashes twice,select

"Forward&Reverse with brake"

Press "Set" button once,

select next option.

Red LED ﬂashes 3 times,select

"Forward&Reverse"

Press "Set" button once,

select next option.

Red LED ﬂashes once, select

"6% Fixed Area "

Press "Set" button once,

select next option.

Red LED ﬂashes twice, select

"9% Fixed Area "

Press "Set" button once,

select next option.

Red LED ﬂashes 3 times, select

"12% Fixed Area "

Press "Set" button once,

select next option.

Red LED ﬂashes once, select

"0% "

Press "Set" button once,

select next option.

Red LED ﬂashes twice, select

"5% "

Press "Set" button once,

select next option.

Red LED ﬂashes 3 times, select

"10% "

......

Press "Set" button once,

select next option.

Red LED ﬂashes 8 times, select

"60% "

Press "Set" button once,

select next option.

......

Press SET button to select the value,

Red LED ﬂashes times shows the item

of value.

Programming with Program Card.

It's the easiest way to set with programming card. Operation is as following: insert signal wire to the interface in programming card , select

the options that you want ( see in the above chart), press【OK】,after VALUE screen displaying "S", this option sets successfully .

If want to reset the option to factory setting, please press 【RESET】, then press【OK】.

(Please see the instruction of program card for more detail)

Protections

If running speed gets slowly (reduce power to cut off in 5 seconds), please reduce speed and stop. ESC red light will ﬂash at

Lipo low-voltage

this time, it means low-voltage protection starts.

protection

For NiMH battery, set no low-voltage protection.

When temperature is higher than 90°, ESC will cut off with ﬂashing green light. When temperature is lower than 80°, motor

will restart again.

Over heat protection

Note : To make ESC not be burnt during working , please don't cancel over heat protection.

Trouble shooting

Troubles

After connecting battery, indicator led

doesn't ﬂash, motor doesn't start ,fan

doesn't start.

Car goes backwards when forward is

pressed.

Stop suddenly during motor rotation.

When motor starts, fast acceleration,

motor gets stuck or pauses.

ptional Kits

Turn

off

ESC

●45A Model with Fan as factory default.

power

●

A,25A,35A without Fan as factory default. according your requirement install or not install.

switch

conﬁrm

and

ﬁnsh

the

setting,

turn

again,

The

ESC

can

work.

Possible causes

Check the soldering of all joints, especially between the battery

1.ESC not powered.

and motor wires.

2.Power supply switch damaged, or switch

If the switch or switch wire is damaged, return to factory for

bad connection.

service.

1.The motor wires may not be connected in

Make sure the motor wires are connected in the correct

the correct sequence.

sequence

1.Receiver meets interference.

See the explanation of low-voltage protection and over heat

2.ESC was protected by battery low-voltage or

protection.

over heat.

1.The battery discharge capacity isn't enough.

1.Change good discharge capacity battery.

2.Motor is too fast or wrong gear ratio is used.

2.Use a slower motor or change the gear ratio .

3.ESC startup acceleration is too fast.

3.Set ESC startup acceleration ( startup mode) slower.

ADD: 5th Floor,C2 Building, Jiaan Industrial Park,

R R

Zone 72,Baoan District, ShenZhen, China

TEL：0755-86321853

FAX：0755-86321852

Web: www.flycolor.net

Email: [email protected]

Solutions

*please pay attention to the "+" and"-"

during install the Fan.

251400-1025-EN V1.1