Astro Pneumatic Tool 1812 매뉴얼

{카테고리_이름} Astro Pneumatic Tool 1812에 대한 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Astro Pneumatic Tool 1812 4 페이지. 1/2" super duty impact wrench

페이지 인쇄

Model:

WARNING

Study, understand and follow all instructions provided with this

product. Read these instructions carefully before installing,

operating, servicing or repairing this tool. Keep these instructions

in a safe accessible place.

INTENDED USE OF THE TOOL

The 1812 and 1812L air impact wrenches are designed to remove

and install threaded fasteners using 1/2" drive sockets designed for

impact wrench use. Do not use this tool outside of the designed

intent. Never modify the tool for any other purpose or use.

WARNING

• Use of this product can expose you to chemicals such as

phthalates which are known to the State of California to

cause cancer, and birth defects or other reproductive harm.

For more information go to

www.P65Warnings.ca.gov/product.

Always wear ANSI approved safety equipment, safety

glasses and clothing when using this product. Study,

understand, and follow all instructions provided with this

product. Failure to read and follow all warnings and

operating instructions may result in damages and serious

injury or death.

• Always wear ANSI approved goggles when using this

product. (Users and Bystanders).

• Never use this tool for any application other than for

which it was designed.

• Only use accessories designed for this tool.

• Never alter or modify this tool in any way.

• Improper operation and/or maintenance of the tool,

modification of the tool, or use of the tool with accessories

not designed for it could result in serious injury or death.

• Always select the correct accessories of the correct size

and design for the job that you are attempting to perform.

• Always work in a clean, safe, well-lit, organized and

adequately equipped area.

• Do not begin repairs without assurance that vehicle is in

secure position, and will not move during repair.

1/2" SUPER DUTY IMPACT WRENCH

1812

1812L

- 3" Anvil

1812L

- 3" Anvil

Product Type:

1/2" SUPER DUTY IMPACT WRENCH

1 YEAR LIMITED WARRANTY

• Astro Pneumatic Tool Co. warrants our products to the original user against

defective material or workmanship for a period of 1 year (except where noted on

our price schedule) from the date of 1st use. Astro reserves the right to determine

whether the product failed because of defective material, workmanship or other

causes and to charge back for missing parts. Astro Pneumatic Tool Co., at its

discretion, will repair products covered under this warranty free of charge. The

distributor should direct the original user to return the product (with the exceptions

listed below) with the distributor's name, address, adequate proof of date of

purchase or a copy of warranty card, and a short note explaining the problem.

Failures caused by accident, alteration, or misuse are not covered by this

warranty.

• Astro Pneumatic Tool Co. or its authorized service representatives must perform

all warranty repairs. Any repair to the product by unauthorized service representa-

tives voids this warranty. The rights under this warranty are limited to the original

user and may not be transferred to subsequent owners.

• This warranty is in lieu of all other warranties, expressed or implied, including

warranties of merchantability and fitness for a particular purpose. Some states do

not allow the exclusion of limitations of incidental or consequential damages so

the above limitations may not apply to you.

PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING

1-800-221-9705 FOR INSTRUCTIONS

When unpacking, check the parts diagram and part number

listing on page 4 to make sure all parts are included. If any

parts are missing or damaged, please call your distributor.

PRODUCT INFORMATION:

• Ideal for general automotive work, light truck, farm, body shop,

tire shop and front-end work

• Durable twin hammer impact mechanism

• Anvil and rotor made of a special heat treated alloyed steel

which prevent chipping or breaking

• Steel hammer case provides maximum protection

• Two piece construction for easy maintenance

• Pressure feed lubrication system

SPECIFICATIONS:

Square Drive:

Free Speed:

Overall Length:

Net Weight:

Max. Torque:

Bolt Capacity:

Air Inlet Thread NPT:

Air Hose I.D. Size:

Avg. Air Consumption:

Air Pressure:

Sound Level

Vibration:

DO NOT DISCARD – GIVE TO USER

Page 1

www.astrotools.com

BEFORE USE

1/2"

7500rpm

7-1/2" (190mm)

5-3/5lbs. (2.60kg)

450ft./lbs.

9/16" (14mm)

1/4"

3/8" (10mm)

4.20cfm

90-120psi

102dBA

6.0M/S²