Flying Mole PM-162d 소유자 매뉴얼

{카테고리_이름} Flying Mole PM-162d에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Flying Mole PM-162d 2 페이지. Digital power amp module

페이지 인쇄

Digital Power Amp Module

PM-162d

Owner's Manual

Thank you for purchasing the PM-162d Digital Power Amp Module.

In order to use the product in a safe manner, please read this Owner's Manual

thoroughly before using.

Also, keep this manual for future reference.

The PM-162d is designed for installation and use in the DPA-M1600.

● PM-162d HT/BI

14. Refer all servicing to qualitied service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the apparatus has been exposed to rain or moisture,

does not operated normally, or has been dropped.

THE MODULE IS NOT WATERPROOFS, TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE AND DO NOT PUT ANY WATER

SOURCE ON THIS MODULE, SUCH AS VASE, FLOWER POT, COSMETICS CONTAINER

AND MEDICINE BOTTLE ETC.

IMPORTANT NOTICE

If this product is found to be the source of interference, which can be determined by turning the unit

"OFF" and "NO", please try to eliminate the problem by using one of the following measures :

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line

filter/s.

In the case of radio or TV interference, relocate/reorient the antenna.

If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer

authorized to distribute this type of product.

If you can not locate the appropriate retailer, please contact Flying Mole Corporation.

Special attention to Transporting This Module

• This module is not designed to be transported when installed in the DPA-M1600.

Make sure each module is removed from the DPA-M1600 and packed individu-

ally before transporting.

• As repair involves servicing individual amp modules, please keep the packaging

materials.

Features

* Each ultra-light unit weighs approximately 1.4kg. (3.08lbs)

* Outstanding power conversion produces a total efficiency of 85%

means low heat generation.

* Ultra-low power consumption is 1/6th of analog amplifiers: 2ch 45W

(when operating at 1/8 rated output at 8Ω).

Cascade Series

● PM-162d HT

● PM-162d BI

Safety Instructions

RISK OF ELECTRIC SHOCK

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALI-

FIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DAN-

GEROUS VOLTAGE CONSTITUTING A

RISK OF ELECTRIC SHOCK IS PRESENT

WITHIN THIS UNIT.

WARNING :

To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

■ The important safety instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer's instruc-

tions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other appa-

ratus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has

two blades with one wider than the other. A grounding type plug has two blades and a third

grounding prong. The wide blade or the third prong are provided for your safety. If the provided

plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cable from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufac-

turer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination

to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

Component Names and Functions

■ Front Panel

■ Rear Panel

● HT Type

● BI Type

CAUTION

DO NOT OPEN

THIS SYMBOL INDICATES THAT THERE

ARE IMPORTANT OPERATING AND MAIN-

T E N A N C E I N S T RU C T I O N S I N T H E

OWNER'S MANUAL WITH THIS UNIT.

q Power Switch/POWER Indicator/LEVEL

Meters

This switch is used to turn the Power of this module ON/

OFF.

The POWER indicator lights when the power is turned ON.

The LEVEL meters light according to the output level.

w INPUT LEVEL Controller

This knob is used to control the input signal level.

The level can be adjusted from 0dB to -30dB. (This level

should normally be set to "0dB" and the volume control on

the preamplifier, etc., that is connected to the amplifier

should be used to control volume.)

e Fastening Screw

This screw is used to secure the unit after it is installed in

the DPA-M1600.

r INPUT Jacks

These jacks are used to supply the ampli-

fier with the input signal.

Connect these jacks to the PRE OUT jacks

on a pre-amplifier, etc.

The XLR (balanced) input wiring on the BI

type is; 1: GND, 2: HOT, 3: COLD.

t SPEAKER Connections

These are the amplifier's speaker outputs.

Connect the jack/terminals to speakers.

Make sure that the impedance of the

speaker connected to the jack is 4Ω or

more.

y AC Power Connector

This is the unit's AC power connector.

AC power is supplied via the DPA-M1600's.