Canon BU-51H 포켓 매뉴얼 - 페이지 20
{카테고리_이름} Canon BU-51H에 대한 포켓 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Canon BU-51H 22 페이지. Canon remote control pan-tilt system
Canon BU-51H에 대해서도 마찬가지입니다: 사용자 설명서 (2 페이지), 포켓 매뉴얼 (22 페이지), 원격 제어 매뉴얼 (2 페이지), 브로셔 및 사양 (4 페이지), 빠른 시작 매뉴얼 (8 페이지)
![Canon BU-51H 포켓 매뉴얼](/uploads/products/server2/1168485/1168485.jpg)
External Extender Control Unit
RE: motorized 2X extender ME: manual 2X extender
Remote Control Accessories
(not available for HJ18ex / HJ14ex)
Four types (82CL-UP800H / 82CL-UP1300H / 105CL-UP900H /
105CL-UP800HD) are available.
Remote Controller
Several models are available.
*The controllers are also applicable to remote control
pro-video lenses.
Connecting Cable
5m, 10m, 20m, 50m and 100m cables are available.
Maximum cable length is 150m by connection of these cables.
Mount Converters for Different Image
Format Size Cameras
Canon offers a variety of Mount Converters to be used between a
lens and a camera of different image format sizes. Each converter
will extend the effective angular field of view of the associated lens
according to the Shift Ratio listed below
Image Size Conversion
Converter
Lens
LO-32BMT
2/3" B4 Mount
1/2" SONY
2/3" B4 Mount 1/2" Standard
LCV-40B
2/3" B4 Mount 1/3" Standard
LCV-42T
LCV-41E
2/3" B4 Mount SONY PMW-EX3 approx. 1.4x
LCV-20E
1/2"
SONY PMW-EX3
*3
*1 SONY's Hot Shoe mount camera, excluding PMW-EX3
*2 1/2" Camera of standard type mount (Panasonic, JVC, Ikegami)
*3 Only applicaple to KH10ex/KH16ex/KH21ex
The other 1/2" mount lenses are not available
Note: The converters are to be used with lenses weighing less then 2.0kg (4.4lbs)
LO-32BMT
LCV-40B
LCV-42T
38
Shift Ratio to
Electronic
Camera
Telephoto Side
Conversion
approx. 1.4x
–––––
*1
–––––
approx. 1.4x
Mount
*2
–––––
approx. 1.8x
Mount
Lens Cable
(12pin) EX3
Hot Shoe(14pin)
Lens Cable
–––––
(12pin) EX3
Hot Shoe(14pin)
LCV-41E
LCV-20E
Optical Shift Image Stabilizer
(Shift-IS) Technology
The history of field lenses is a history of zoom ratio/focal length
extension. It came to a point where the industry thought it would be
impossible to push the envelope any further. The telephoto focal
length of the lens became so long that even the slightest amount of
wind or operator movement would cause image shake and viewing
the picture became intolerable. This was before Canon announced
the incredible magnification of the DIGISUPER 86xs zoom lens.
Canon, renowned for its optical image stabilization technologies,
developed another new stabilization solution for the broadcast field
lens, a built-in Optical Shift Image Stabilizer (Shift-IS) to overcome
image shaking at telephoto focal lengths. Now, the Shift-IS is
employed in the following lenses:
DIGISUPER
100AF
DIGISUPER 100xs
DIGISUPER
86AF
DIGISUPER 86IIxs
DIGISUPER 86IITELExs
DIGISUPER 75xs
HJ40x Series
How the Optical Image Stabilizer (Shift-IS) Works.
When the lens moves, the light rays from the subject are bent
relative to the optical axis, resulting in an unsteady image
because the light rays are deflected. By shifting the IS lens group
on a plane perpendicular to the optical axis to counter the degree
of image shake, the light rays reaching the image plane can be
steadied. Since image shake occurs in both horizontal and
vertical directions, two shake-detecting sensors for yaw and
pitch, detect the angle and speed of movement and send this
information to a high-speed 32-bit microcomputer, (which
converts the information into drive signals for the IS lens group).
Then, the actuator moves the IS lens group horizontally and
vertically, thus counteracting the image shake and maintaining a
stable picture. The Shift-IS component is located within the lens
groups and is most effective for lower frequency movements
caused by platform vibration or wind effect without increasing the
overall size and weight of the master lens.
39