Canon EF35mm f/1.4L USM 지침

{카테고리_이름} Canon EF35mm f/1.4L USM에 대한 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Canon EF35mm f/1.4L USM 2 페이지. Large-diameter wide-angle lens for eos cameras
Canon EF35mm f/1.4L USM에 대해서도 마찬가지입니다: 지침 (2 페이지), 지침 (2 페이지), 지침 (2 페이지), 사용자 설명서 (5 페이지)

페이지 인쇄

EF Lenses

EF35mm f/1.4L II USM

Instructions

Thank you for purchasing a Canon product.

EF35mm f/1.4L II USM is a large-diameter wide-angle lens for EOS cameras.

"USM" stands for Ultrasonic Motor.

●

Safety Precautions

Do not look at the sun or a bright light source through the lens or

●

camera. Doing so could result in loss of vision.

Looking at the sun directly through the lens is especially hazardous.

Whether it is attached to the camera or not, do not leave the lens under

●

the sun without the lens cap attached. This is to prevent the lens from

concentrating the sun's rays, which could cause a ﬁre.

Handling Cautions

●

If the lens is taken from a cold environment into a warm one,

condensation may develop on the lens surface and internal parts. To

prevent condensation in this case, ﬁrst put the lens into an airtight plastic

bag before taking it from a cold to warm environment. Then take out the lens

after it has warmed gradually. Do the same when taking the lens from a warm

environment into a cold one.

●

Do not leave the lens in excessive heat such as in a car in direct sunlight.

High temperatures can cause the lens to malfunction.

Usage Precautions

●

When using this lens, please check the Canon website for the latest camera

ﬁrmware. If the camera's ﬁrmware is not the latest version, be sure to update

to the latest ﬁrmware.

●

For details on updating ﬁrmware, please check the Canon website.

Conventions used in this instruction

Warning to prevent lens or camera malfunction or damage.

Supplementary notes on using the lens and taking pictures.

Nomenclature

Focusing ring

①

●

Hood mount

②

●

Filter mounting thread

●

③

Distance scale

④

●

⑤

●

Rubber ring

●

⑥

Focus mode switch

⑦

●

Lens mount index

⑧

●

Contacts

1. Mounting and Detaching the Lens

See your camera's instructions for details on mounting and detaching the

lens.

●

After detaching the lens, place the lens with the rear end up to prevent

the lens surface and contacts from getting scratched.

●

If the contacts get soiled, scratched, or have ﬁngerprints on them,

corrosion or faulty connections can result. The camera and lens may not

operate properly.

●

If the contacts get soiled or have ﬁngerprints on them, clean them with a

soft cloth.

●

If you remove the lens, cover it with the lens cap and dust cap. To attach

the dust cap properly, align the lens mount index and the

dust cap, and turn clockwise

❶

. To remove it, reverse the order.

●

The lens mount has a rubber ring for enhanced dust- and water-

resistance. The rubber ring may cause slight abrasions around the

camera's lens mount, but this will not cause any problems. If the rubber

ring becomes worn, it is replaceable by a Canon Service Center at cost.

2. Setting the Focus Mode

To shoot in autofocus (AF) mode, set the focus mode switch to AF

To shoot in manual focus (MF) mode, set the focus mode switch to MF, and turn

the focusing ring to set the focus

❸

The focusing ring always works, regardless of the focus mode.

When the camera AF mode is ONE SHOT AF, focus manually by pressing

the shutter button halfway and turning the focusing ring. (Full-time manual

focus)

❶

●

❷

●

○

index of the

❷

❸

●