COLAMY 2181 사용 설명서 - 페이지 2

{카테고리_이름} COLAMY 2181에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. COLAMY 2181 2 페이지.

페이지 인쇄

WARNING

Please read the instructions carefully and follow the assembly steps.

To ensure proper assembly, please follow all steps and use all parts provided. Not following

this warning may result in serious injury to you or others.

To prevent misalignments, keep the screws loose and do not tighten them until they are all

in their correct positions.

Avoid overtightening or forcing the screws, as this could cause them to break, strip, or

damage the threads of the holes.

Using the wrong size of screws for a particular part could cause damage to the screw or the

part.

Please lubricate all moving parts regularly and tighten all bolts and screws every 6 months,

or as needed.

PRODUCT FEATURES

Pneumatic Seat Height

Adjustment

Pulling the lever upwards enables

height adjustment of the seat, then

the seat can be locked at a fixed

height by releasing the lever.

Rock Tension Adjustment

Simply adjust the knob

counterclockwise to tighten the tension

Tight

of rocking. Or loosen the tension by

Loose

turning the knob clockwise whenever

needed.

Seat Back Locking Mechanism

Simply press the lever down to lock

the seat in an upright position.

SAFETY INFORMATION

WEIGHT CAPACITY FOR SEATING: 400LBS

Do not sit at the front edge

Do not stand on the chair

Do not use the chair with more

than one person

of the chair

Sit in the center of the

chair with your back

against the backrest

Do not push the chair around

Do not push down on the

Do not place all your weight

when a person is sitting in it

backrest when a person is

on the backrest only

reclined

ASSEMBLY PARTS AND TOOL

BEFORE YOU GET STARTED, A FEW POINTERS:

Having a friend to help makes

Mind the important safety

assembly extra-easy

information

Casters *5

Star Base *1

Lift *1

Seat Plate *1

Seat Cushion *1

Back Cushion *1

Arms*2

Lift Cover *1

1 1

Bolts M6*25mm *4

Bolts M8*25mm *4

Bolts M8*35mm *8

Plastic Caps *8

Wrench *1

PLEASE MAKE SURE ALL THE PARTS ARE INCLUDED.

MISSING PARTS?

[email protected]

ASSEMBLY INSTRUCTIONS

Turn the Star Base(2) upside down, then press the Casters(1) into the holes at the end of

Step 1

each base leg, insert the Lift(3) into the center hole of the Star Base(2), the Lift Cover(8)

should be placed over the Lift(3).

Align the Seat Plate(4) over the pre-drilled holes underneath the Seat Cushion(5), make

Step 2

sure that the front of the Seat Plate is facing the front of the Seat Cushion. Attach the Seat

Plate to the Seat Cushion using FOUR Bolts M8*25mm(10), tighten all the bolts with the

Wrench(13), being careful not to miss-thread the bolts or damage the seat.

front

Bolts M8*25mm *4

Wrench *1

Align two control handles of the Seat Plate(4) over the pre-drilled holes underneath

Step 3

the Seat Cushion(5), attach these two handles to the Seat Cushion using FOUR Bolts

M6*25mm(9), tighten all the bolts with the Wrench(13).

front

Bolts M6*25mm *4

Wrench *1

Turn the Seat Cushion(5) upright and align the center hole of the Seat Plate over the

Step 4

Lift(3), then push the Seat Cushion down onto the Lift firmly until the connection is secure.

Attach the Arms(7) to the Seat Cushion(5) with FOUR Bolts M8*35mm(1 1) by using the

Step 5

Wrench(13).

Note 1: Arm rests are labeled with an "L" (left) or "R" (right) to show which sides they should be

placed on.

Note 2: Do not tighten all the bolts to 100%, make sure it has space to adjust in the next steps.

1 1

Bolts M8*35mm *4

1 1

Wrench *1

Lay the Back Cushion(6) on the seat of the chair with the top of the cushion toward the

Step 6

front. Attach the Back Cushion to the Arms(7) with TWO Bolts M8*35mm(1 1) screwed to the

LOWER holes by using the Wrench(13).

Note: Avoid tightening all the bolts to 100% at this stage and leave some space for adjustments in the

next steps.

1 1

Bolts M8*35mm *2

Wrench *1

Rotate the back of the chair up, then secure it with the TOP TWO Bolts M8*35mm(1 1)

Step 7

with the Wrench(13). Adjust the balance on each side of the chair, and fully tighten all the

bolts at this step.

1 1

Bolts M8*35mm *2

Wrench *1

Press the Plastic Caps(12) into the Arms holes to cover the bolts.

Step 8

Plastic Caps *8

1 1