Air Gunsa AZ3 HTE2 사용 설명서 - 페이지 2
{카테고리_이름} Air Gunsa AZ3 HTE2에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Air Gunsa AZ3 HTE2 4 페이지. Spray gun
Air Gunsa AZ3 HTE2에 대해서도 마찬가지입니다: 사용 설명서 (9 페이지), 사용 설명서 (17 페이지)
페이지 인쇄
MAINTENANCE & INSPECTION
CAUTION
- Make sure you do not damage tip of fluid nozzle or seat section.
- Never use spare parts that are not Air Gunsa originals.
1. Pour remaining paint into another container. Clean fluid passages and
air cap set. Place a small amount of cleaner into the cup and flush out the
fluid passages. NOTE: DISCONNECT ATOMIZING AIR
DO NOT ATOMIZE CLEANING SOLUTION.
- INCOMPLETE CLEANING CAN CAUSE PATTERN SHAPE DEFECTS.
ESPECIALLY CLEAN FULLY AND PROMPTLY AFTER USE WITH TWO-
COMPONENT PAINT.
2. Clean each section with brush soaked with cleaner and wipe out with
waste cloth.
- NEVER IMMERSE THE SPRAY GUN COMPLETELY IN SOLVENT, AS IT
CAN DAMAGE PARTS.
3. Before disassembly, clean fluid passages.
a. Disassemble fluid nozzle, while keeping fluid needle pulled (trigger-
ing) in order to protect its seat section.
b. Disassemble fluid needle set. (only when strictly necessary)
c. Remove the fluid adj. knob and needle spring, extracting the spring
and fluid needle set, from the back of fluid adj. guide set still assem-
bled on the gun body.
Leakage from fluid nozzle set and fluid needle set seat sections.
Replace fluid nozzle set and fluid needle set, if leakage does not stop
after cleaning them. If you replace fluid nozzle or fluid needle only, match
them carefully and make sure there is no further leakage.
2
TROUBLESHOOTING
GUN DOES NOT SPRAY
- Fluid adj. knob closed.
- Tip hole of nozzle obstructed.
- Paint filter obstructed.
- Non drip obstructed.
INTERMITTENT SPRAY PATTERN
- Air escapes from fluid nozzle.
- Air escapes from fluid needle
packing.
- Air escapes from cup joint or
fluid hose joint .
- Dirt inside air cap.
DEFECTIVE SPRAY PATTERN
- Dirty nozzle or air cap.
Nozzle or air cap has been
damaged.
- Fluid nozzle is loose
- Paint viscosity too high or
too low.
- Fluid output too high or
too low.
LEAKING
- Fluid nozzle seat or needle set
dirty, damaged or worn.
- Loose fluid needle adj. knob.
- Fluid needle spring is worn.
- Loose fluid nozzle.
- Needle packing set loose, too
tight, dirty or worn.
AIR ESCAPES FROM AIR CAP
- Air valve, air valve seat or air
valve spring dirty or damaged. sary.
DECLARATION OF CONFORMITY
We AIR GUNSA s.r.l. - Corso Vigevano, 46 - 10155 Torino - Italy declare, under our
sole responsibility, that the product:
AZ3 HTE2 SPRA Y GUN series
to which this declaration relates, is in conformity with European ATEX Directive
94/9/CE for use in zone 1 and zone 2 and Machinery Directive 98/37/CE.
According with the following international requirements: EN 1127-1, EN 292-2 and
EN 1953.
Name and position of issuer: Mr. Marco G. VICENTINI, Managing Director
Firma:
This is an original CE declaration of conformity issued by AIR GUNSA s.r.l.
Other copies are considered not valid
Check and adjust.
Check and clean.
Check and clean.
Check and clean.
Check , clean & replace if
necessary.
Tighten.
Tighten.
Clean.
Clean carefully.
Replace If damaged.
Tighten.
Dilute paint or increase
viscosity
Adjust fluid adj. knob to
reduce or increase.
Clean or replace if neces-
sary.
Adjust.
Replace.
Tighten.
Adjust, clean or replace.
Clean or replace if neces-
data: 04/04/2008