Air Gunsa AZ30 HTE 사용 설명서

{카테고리_이름} Air Gunsa AZ30 HTE에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Air Gunsa AZ30 HTE 8 페이지.

페이지 인쇄

Before commencement of work thoroughly read this Manual and its instructions, including those regarding safety of work,

and strictly observe them.

This spray gun has been manufactured in compliance with the CE 94/9/EC

standard and safety standard II 2G X, intended for work in hazard zones 1 and 2,

symbol X indicates that the spray gun is provided with antistatic protection, and

electric charges should be carried away by an air conduit earthing system.

The spray gun should be operated by a trained worker. Any use and/or servicing not in compliance with this manual will

INVALIDATE THE WARRANTY. Read these instructions before using the spray gun. AIR GUNSA will not be held

responsible for mechanical damage due to a fall of the tool, or for any damage resulting from improper

maintenance/servicing, and/or operation of the spray gun. All information regarding maintenance and operation is

provided in this manual booklet. In case of damage in transport, missing parts, or if any additional information is required,

please contact your nearest AIR GUNSA distributor.

Before commencement of work carefully read all instructions marked IMPORTANT, or ATTENTION, as failure to do so

may result in abnormal functioning of the spray gun and/or its damage. Moreover, please read all guidelines marked with

the

symbol.

ATTENTION

WARNING

IMPORTANT

IMPORTANT TECHNICAL INFORMATION

Max. working pressure: 7.0 bar (100 PSI)

Noise level measured in (LAeqT): 73.5 dB (A)

Lacquering conditions: recommended conditions listed in

the specifications

Space: 1m around the spray gun, 1.6 m above the spray

gun

SPECIFICATIONS

Model

Nozzle

diameter

mm (in)

AZ30 HTE Gravity feed

AZ30 HTE 1.0

1.0 (0.039)

AZ30 HTE 1.3

1.3 (0.051)

AZ30 HTE 1.5

1.5 (0.059)

AZ30 HTE 1.8

1.8 (0.070)

AZ30 HTE 2.0

2.0 (0.079)

(1) Pressure was measured at the air gun inlet with release trigger pressed.

(2) Lacquer output for 21 sec., using Ford cup no. 4.

Manufactured by: AIR GUNSA_ANEST IWATA Group

INSTRUCTION MANUAL

AZ30 HTE SPRAY GUN

This symbol indicates a potentially dangerous situation. Failure to follow instructions marked

with this symbol may contribute to health problems or death.

This symbol indicates a potentially dangerous situation. Failure to follow instructions marked

with this symbol may contribute to health problems or death.

This symbol indicates information deemed important by the manufacturer. In this manual,

description of hazards is limited to the necessary minimum. However, the user should

remember to observe international, national, and in-house safety rules concerning the

following hazards and issues: electric shock, explosion hazard, gases, protective clothing, etc.

Head

(1)

Pressure

bar (PSI)

10HP

2.5 (36)

13HP

15HP

18HP

20HP

IMPORTANT

Temperature range:

for atmosphere: 5~40 °C

for lacquer and compressed air: 5~43 °C

Paint tank terminal: 1/4" - F

Air inlet terminal: 1/4" - M

(2) Lacquer

output

consumption

ml/min

NL/min

Recommended values

175

220

280

315

Air

Jet width

mm (In)

245

150 (5.9)

245

225 (8.85)

250

260 (10.23)

270

325 (12.79)

270

350 (13.77)

Weight

With tank

640

Without tank

490