Air Gunsa AZ30 HTE 1.8 사용 설명서

{카테고리_이름} Air Gunsa AZ30 HTE 1.8에 대한 사용 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Air Gunsa AZ30 HTE 1.8 4 페이지. Spray gun az30 hte m&s cup

페이지 인쇄

AIR GUNSA s.r.l.

46, Corso Vigevano

Quality Air Spray Guns Since 1944

10155 Torino - Italy

Tel. ++39 011 24 80 868

www.anest-iwataeu.com/airgunsa

Fax ++39 011 22 74 406

ANEST IWATA Europe S.r.l.

46, Corso Vigevano

10155 Torino - Italy

Tel. ++39 011 24 80 868

Fax ++39 011 22 74 406

www.anest-iwataeu.com

e-mail: [email protected]

Instruction Manual

SPRAY GUN AZ30 HTE, AZ30 HTE M&S CUP

Before use, adjustment or maintenance, it is important to read this instruction manual very

carefully. This manual must be stored in a safe place for any future reference that may be necessary.

This AIR GUNSA spray guns kit complies to ATEX regulations 94/9/EC, protection level:

II 2 G X Suitable for using Zones 1 and 2.

X marking: Any static electricity discharge from the spray gun is to be diverted to the ground via the conductive air hose as stipulated.

This spray gun should be operated only by an adequately trained operator, for safe use and maintenance of the equipment. Any

misuse or handling other than those indicated in this Instruction Manual is not covered by guarantee. AIR GUNSA disclaims all

responsibility for any accident or damage caused by failure to observe the operational and safety procedures as from this man-

ual. In the interest of user friendliness, this manual contains information in a brief and concise form.

For any additional information you may require regarding spray guns operations, or if any missing parts or any damage during

transportation is found, please contact your nearest AIR GUNSA Company (see last cover page).

Be sure to observe warnings and cautions in this instruction manual.

If not, it can cause paint ejection and serious bodily injury by drawing organic solvent.

Be sure to observe following

WARNING Indicates a potentially hazardous situation which, if not avoided, may result in serious injury or loss of life.

CAUTION

IMPORTANT

IMPORTANT SPECIFICATIONS

Max. Pressure:

Noise Level (LAeqT)

Spray conditions

Measuring point

TECHNICAL SPECIFICATIONS

Model

AZ30 HTE Gravity feed

AZ30 HTE 1.0

AZ30 HTE 1.3

AZ30 HTE 1.5

AZ30 HTE 1.8

AZ30 HTE 2.0

Distributed by:

(1) Atomizing air pressure means air pressure at gun inlet when trigger is pulled and air flows.

(2) Paint viscosity; 21sec/Ford cup#4

Manufactured by: AIR GUNSA _ Anest Iwata Gruop

IMPORTANT

marked items which are especially important.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury or pro-

perty damage.

Indicates notes which we ask you to observe. The safety precautions in this instruction manual are the mini-

mum necessary conditions. Follow national and local regulations regarding fire prevention, electricity and

safety as well as your own company regulations.

7.0 bar (100 PSI)

73.5 dB (A)

Recommended condition in Tech. Specifications

1m backwards from gun, 1,6 m height

Recommended condition

Nozzle Orifice Air Cap

(1)Atomizing

(2) Fluid

set Mark

Air pressure

Output

Consumption

Ø mm (in)

bar (PSI)

ml/min

Nl/min (cfm)

1.0 (0.039)

10 HP

1.3 (0.051)

13 HP

175

1.5 (0.059)

15 HP

2.5 (36)

220

1.8 (0.070)

18 HP

280

2.0 (0.079)

20 HP

315

Max. Temperature:

Atmosphere

5 ~ 40 °C

Air and fluid

5 ~ 43 °C

Air connection:

G 1/4"

Fluid connection:

G 1/4"

Air

Pattern

Weight

Width

Without Cup

With Cup

mm (in)

g (lbs)

245 (8.65)

150 (5.90)

600 cc CUP

245 (8.65)

225 (8.85)

640 (1.41)

490 (1.07)

------------

250 (8.82)

260 (10.23)

M&S CUP

270 (9.53)

325 (12.79)

664 (1.46)

270 (9.53)

350 (13.77)