Canon Pixma Pro9500 Series 설정 지침

{카테고리_이름} Canon Pixma Pro9500 Series에 대한 설정 지침을 온라인으로 검색하거나 PDF를 다운로드하세요. Canon Pixma Pro9500 Series 2 페이지. Printing on the fine art metal series
Canon Pixma Pro9500 Series에 대해서도 마찬가지입니다: 매뉴얼 (31 페이지), 설정 지침 (2 페이지), 보충 설명서 (6 페이지), 기술 사양 (2 페이지), 매뉴얼 (25 페이지), 빠른 시작 매뉴얼 (20 페이지), 빠른 시작 매뉴얼 (2 페이지), 빠른 시작 매뉴얼 (3 페이지)

페이지 인쇄

Q T 5 0 1 4 4 V 0 2

Unpack the Printer

Carefully remove all items from the box.

PIXMA Pro9500 series

Photo Printer

Documentation and

Software Kit

PIXMA Pro9500 series

Print Head

Power Cord

PGI-9MBK

Matte

PGI-9PBK

PGI-9PC

Black

Photo

PGI-9PM

PGI-9GY

Photo

Black

Cyan

Gray

Magenta

PGI-9C

Cyan

PGI-9Y

PGI-9G

Yellow

Green

PGI-9M

PGI-9R

Magenta

Red

Remove the tapes from the printer.

NOTE:

· It takes about an hour to complete the setup of the

printer.

· A USB cable is necessary to connect the printer

with your computer.

Prepare the Printer

Plug the power cord into the back of the printer

and connect the other end to a power outlet.

Press the POWER button. The printer will

initialize. Wait until the POWER lamp displays a

steady blue light.

POWER Lamp

POWER Button

Open the Front Tray. Raise the Top Cover.

NOTE: Gently press the

mark on the

Front Tray. The Front Tray automatically opens.

Top Cover

Front Tray

The Print Head Holder automatically moves to

the center. Remove the protective tape from

the Print Head Holder. The tape position is

subject to change.

Protective Tape

Write down the serial number located inside

the printer. You will need this to register your

products.

Serial Number Location

IMPORTANT: If the Top Cover is left open for

more than 10 minutes, the Print Head Holder

moves to the right. Close and reopen the Top

Cover to return the holder to the center.

Start Here

Easy Setup Instructions

Install the Print Head

Firmly raise the print head lock lever.

Remove the Print Head from its package.

Nozzles

Tear at notch to open

CAUTION: There might be some transparent or

light color ink on the inside of the bag the Print

Head comes in - this has no effect on print

quality. Be careful not to get ink on yourself

when handling these items.

NOTE: Do not touch the nozzles.

Remove and discard the orange protective cap

from the Print Head.

CAUTION: There might be some transparent or

light color ink on the inside of the protective

cap - this has no effect on print quality. Be

careful not to get ink on yourself when handling

these items.

NOTE:

· Do not touch the print head nozzles and the

electrical contacts.

· Do not attempt to reattach the protective cap once

it has been removed.

Electrical

Print Head

Contacts

Nozzles

Slide the Print Head into the holder.

The Print Head will rest at a slight angle.

Electrical

Contacts

NOTE: Do not touch the electrical contacts.

Lower the print head lock lever carefully.

Install the Ink Tanks

Remove the Red Ink Tank (PGI-9R) from its

package.

Remove and discard the orange protective cap

located on the bottom of the ink tank.

IMPORTANT: Do not touch the electrical

contacts.

NOTE:

· To avoid spilling ink, never press on the sides of

an ink tank.

· Do not touch the open ink port once the protective

cap is removed, as this may prevent the ink from

being ejected properly.

Electrical Contacts

Protective Cap

Ink Port

Insert the ink tank into the rightmost slot.

Press the

mark on the ink tank until it clicks

into place and then its lamp lights red.

click

Ink Lamp

Insert the remaining nine ink tanks into their

assigned slots. Ensure that ink lamps light red.

Refer to the color

guide on the print

head lock lever.

Close the Top Cover. Lift open the Paper

Support and the Paper Support Extension, then

pull out the Front Tray Extension.

Paper Support

Extension

Paper Support

Top Cover

Front Tray Extension

NOTE: If the ALARM lamp on the printer flashes

orange after you have closed the Top Cover, an

ink tank may not be installed properly. Open the

Top Cover and make sure that the ink tanks are

installed in the correct order directed on the

label.

series

Photo Printer

Connect the Printer

and Load Paper

IMPORTANT: When the POWER lamp flashes

blue and the printer vibrates, the printer is

shaking the ink tanks. Once you have installed

the ink tanks and have closed the Top Cover,

wait for about 2 minutes 30 seconds until the

POWER lamp stops flashing and stays lit, and

the printer has stopped making operating

noises before proceeding. Do not open the Top

Cover while the printer is operating (the POWER

lamp is flashing blue).

TURN THE PRINTER OFF.

IMPORTANT: Be sure the printer is off before

continuing, or the computer will attempt to

install the printer driver before the printer is

ready.

Connect one end of the USB cable to the

computer, the other to the appropriate USB

port on the printer.

NOTE: The Pro9500 series Photo Printer is

equipped with USB 2.0 Hi-Speed port. If your PC

does not support USB 2.0 Hi-Speed, or if any

non-certified USB 2.0 cable or driver is used for

the connection, the printer will operate at a

lower speed provided under USB 1.1.

USB Port

USB Cable

Pinch the Paper Guide and slide it to the left.

Load two sheets of plain paper into the Auto

Sheet Feeder, align the paper with the right

edge of the Auto Sheet Feeder, then slide the

Paper Guide toward the left edge of the paper.

Auto Sheet

Feeder

Print Side

Paper

Guide

IMPORTANT: Print Head Alignment (Step 6)

requires that letter size paper is loaded in the

Auto Sheet Feeder (top paper feeder).

Continue with Step 6

on the back page.