Advance acoustic Reel Cleaner 56108050 운영자 매뉴얼 - 페이지 9

{카테고리_이름} Advance acoustic Reel Cleaner 56108050에 대한 운영자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Advance acoustic Reel Cleaner 56108050 12 페이지.

페이지 인쇄

Advance acoustic Reel Cleaner 56108050 운영자 매뉴얼

1. Maintenance and Use

BALL FLOA

BALL FLOAT V

BALL FLOA

T V

T VAC SHUTOFF

T V

AC SHUTOFF

When the recovery tank is full, the float system will shut off the incoming air flow and prevent water from entering the vacuum motor. The float

may not work properly if the float filter is clogged or if there is heavy foam in the tank.

CAUTION!

To avoid vacuum motor damage, always make sure the float filter is clean and the ball travels freely before turning

on the machine and use a defoamer whenever foam is present.

MAINTENANCE AND USE:

1 1 1 1 1

Use only approved chemicals at the recommended mix ratios. All chemicals should be added through the feed system (17)

directly to the tank solution. Possible damage to pump, seals or other components could result.

2 2 2 2 2

For optimum performance, flush the Chemical Feed Lines (17)

spraying until the stream runs clear. See Maintenance Schedule below.

3 3 3 3 3

Pump seals may need to be replaced at 1,000 hours of use or if the pump begins to leak. The pressure regulator valve will need to be rebuilt

when a drop in spraying pressure is apparent.

4 4 4 4 4

Prior to each job, inspect, and clean if needed, the Solution Filter (12)

5 5 5 5 5

Fill the Solution Tank (2)

(2) with clean water. Using warm water is a benefit in cleaning effectiveness, but do not run hot water (140 degrees

(2)

or more) through the pump.

6 6 6 6 6

(19)

Plug in the Power Cord (19)

(19)

(19). Attach the priming hose to the outlet Quick Disconnect (9)

Recovery Tank, and turn the pump on (A)

attach the Spray Hose (6)

(6)

(6).

(6)

7 7 7 7 7

Place chemical in the holder and insert one of the Feed Lines (17)

feed when the Chemical Valve (C)

= low; back = high).

8 8 8 8 8

Set the Spray Gun (7)

(7) to low pressure. Turn the pump on (A)

(7)

9 9 9 9 9

Begin cleaning.

MAINTENANCE SCHEDULE

Check / Clean Vacuum Float Shutoff

Check Vacuum Motor Airways

Check Carbon Brush Wear on the Vacuum Motor

Have Nilfisk-Advance check the carbon motor brushes once a year or after 500 operating hours.

IMPORT

IMPORTANT!

IMPORT

ANT!

IMPORT

ANT!

Motor damage from failure to service the carbon brushes is not covered under warranty.

TECHNICAL SPECIFICA

TECHNICAL SPECIFICATIONS

TECHNICAL SPECIFICA

Vacuum Motor

Water lift

Air Flow

Tank Construction

Solution Tank Capacity

Recovery Tank Capacity

Application Flow

Solution Hose Length

Recovery Hose Length

Blower Hose

Power Cord

Rear Wheels

Front Casters

Height

Length

Width

Machine Weight

Shipping Weight

(17)

(17) by replacing the chemical container with a container of clear water and

(17)

(A). Run until the pump is fully primed (no visible air in the water flow). Turn the pump off (A)

(A)

(17)

(17) into the container. Secure it by screwing on the cap. The chemical will

(17)

(C)

(A)

(A) and spray through the tool for a few seconds to fill the line with solution.

MAINTENANCE ITEM

Daily

MAINTENANCE ITEM

Daily

Flush Chemical Lines (17)

(17)

Clean Solution Filter (12)

(12)

Lubrication

TIONS

3 stage, 12 amp, 1400 watt, 110v/60Hz

117" (297 cm.)

100 cfm (2832 l./min.)

Rotational Molded Polyethylene

25 gallon (11.3 l.)

22 gallon (10 l.)

300 psi @ nozzle, 1 gpm

50 feet (15.25 m.)

25 feet with 1.5" diameter (15.25m. X 3.8 cm)

13 feet (4 m.)

50 feet safety yellow w/GFCI (15.25 m.)

2 - 10" (25 cm.)

2 - 4" w/ brake (10 cm.)

40" (101 cm.)

36" (91 cm.)

21" (53.3 cm.)

135 lbs (61.2 kg)

180 lbs (81.6 kg)

(12). Check the recovery tank float filter (4)

(12)

(9)

(9). Place the open end of the priming hose into the

(7)

(7) is used in the low pressure setting (forward

(7)

Weekly

Monthly

Weekly

Monthly

FORM NO. 56041549 - Reel Cleaner

(17) and not added

(17)

(4)

(4) for debris prior to each job.

(A)

(A) and

(A)

Yearly

™

- 9 9 9 9 9