Daema DWP-55 사용자 설명서 - 페이지 5
{카테고리_이름} Daema DWP-55에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. Daema DWP-55 5 페이지. Electric thermo pot
페이지 인쇄 Once the Re-boil button is pressed, the boiling process cannot
be reset until the dispenser automatically switches to Keep
Warm mode.
Do not press the Re-boil button repeatedly as the continuous
boiling process may cause unit to malfunction.
Cleaning and Maintenance
Disconnect power and allow appliance to cool before cleaning.
Disconnect power from wall outlet and remove cord from receptacle.
Detach upper lit and pour out remaining water. Be cautious if water is hot.
Do not wash under running water. Do not place in a dishwasher or dryer.
Do not wet the control panel and receptacle.
Do not leave water in pot unused for long period of time.
Do not turn unit upside-down to dry.
Do not immerse any part of the dispenser in water or any liquid.
Do not use bleach, alcohol or other harsh chemicals
Do not scrub with metal pads or sharp objects.
Upper lid must be detached when pouring out water.
Do not handle plug when hands are wet or damp.
Minerals in tap water may cause white residue to attach to the surface of
the inner tank. They sometimes change the color of the inner tank (reddish
or black). Clean the interior frequently to avoid this problem.
Lid and body
Wipe clean with damp cloth.
Inner pot and inner lid
Use soft sponge to clean and rinse with water. The amount of build-up and stain
depends on the quality of water and times of boiling. The inner pot should be
cleaned once a month. If extremely dirty, use Citric Acid, lemon or lime juice:
approximately 1 oz. of the preferred solution.
Add
Add
water to the full line, close lid and connect power.
solution to boil and soak for 30~60 minutes.
Allow
ispense a few cups of solution to clean the piping.
D
Disconnect power and allow unit to cool.
Remove lid and pour out solution, rinse clean.
If lemon was used, to remove the smell of lemon, fill with clean water,
boil and dispose.
DO NOT use: dish soap, scrubbing powder or brush, benzine, thinner
or any harsh chemicals.
When not in use for an extended period of time, clean and let dry
completely before storage. Store in original packaging or plastic
bag and keep in a cool, dry place.
-6-
Trouble Shooting
SYMPTOM
Water does not boil when plugged
in. (Power LED on)
Unit will not switch to Keep Warm
Unit will not switch to Boil
Auto pump does not work or not
working efficiently
Water is flowing out from unit
White substance floating in water
Boiling sound is excessively loud Interior is dirty and needs cleaning.
Hot water has unpleasant odor or
taste
Products bearing the crossed out bin symbol are not to
be disposed with your general household waste. For
the correct collection and treatment of these products,
take them to the collection points designated by your
local authority. Alternatively contact the retailer who
sold you the product.
POSSIBLE CAUSE
Dirty inner pot. Added water is already
hot. Water level is below refill line.
Unit may not function properly if used in
high elevation or in very cold or hot
conditions. In such conditions, unit may
keep boiling or not reach boiling point.
Water level is too low. Dirty inner pot
Unit not plugged in.
Immediately after boiling, bubbles may
form which makes it difficult to dispense.
Open the lid to release steam.
The interior is dirty and needs cleaning
Water is filled above the FULL line.
These are mineral deposits. (Not erosion
of inner pot.) Clean the unit according to
the instructions under Maintenance
Resin used in manufacturing may give off
a mild odor. This will disappear with use.
Due to chlorine in water – reboil the water
-7-