Dot-Spot clarios-mini 운영자 매뉴얼 - 페이지 12
{카테고리_이름} Dot-Spot clarios-mini에 대한 운영자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Dot-Spot clarios-mini 15 페이지.
Dot-Spot clarios-mini에 대해서도 마찬가지입니다: 운영자 매뉴얼 (20 페이지)
페이지 인쇄Assembly
The switching point of the luminary between on and off for the PWM level is not defined: Ideally it
should be worked with a switching impulse between ground and open contact or optionally with an
impulse between ground and operating voltage. A PWM signal differing from the operating voltage
is not allowed.
Free cabling
The connection is made according to the assignment tables. The connection must be carried out
according to the required IP classification.
clarios-mini white / monochromatic
Wire color
red
blue
black
Attention:
In case the luminary is used without the dimming function, the PWM line (wire for the
PWM signal) must be connected to ground (-). Otherwise the LED remains off.
Connection diagram of the clarios-mini white / monochromatic without dimmer
See respective drawing in the middle of this manual (p. 14).
Connection diagram of the clarios-mini white / monochromatic with dimmer
See respective drawing in the middle of this manual (p. 14).
clarios-mini RGB
Wire color
white
red
green
blue
black
Attention:
The cable of the clarios-mini RGB features a wire which is not used (brown or gray).
Normally, the wire is shortened ex works and should not be connected.
Connection diagram of the clarios-mini RGB
See respective drawing in the middle of this manual (p. 15).
22
Assignment
+ 12 Volts
S-PWM
ground (-)
Assignment
+ 12 Volts
red S-PWM
green S-PWM
blue S-PWM
ground (-)
Assembly
M12 plug and cabling system
The connection of the clarios-mini versions with M12 connector is quite simple, either with or
without dimming function. Plug the connector of the luminary in a free socket of the M12 cabling
system. The M12 cabling system is coded in a way to avoid wrong wiring or failures.
Please plan the components required for the electrical installation (power supplies, distributors,
extensions and plugs for unassigned M12 sockets) according to the sales documentation of the
M12 cabling system before placing an order.
Assignment of the M12 connector system
Pin number
Wire color (if plug
5-pin plug clarios-mini
M12 plug
is pinched off)
white / monochromatic
1
brown
S-PWM
2
white
3
blue
12 V +
4
black
5
green/yellow (gray)
ground (-)
Operation
LED lights are extremely energy efficient and, under normal operation, have a very long life. To
ensure the maximum life of the LED and to increase the energy efficiency, the following should be
considered:
■ The turning on and off of the luminary should be carried out by the input circuit of the power
supply.
■ The turning off of the luminary via the PWM signal should not occur permanently since in this
case the electronics unit of the luminary continues operating.
■ Even if the luminary is equipped with a THERMOPROTECT system that protects the luminary
against thermal damage, a permanent abnormal operation should be avoided.
■ The heat dissipation of the LED must not be hindered. Therefore, do not cover the spot.
■ Avoid operating the spot in case of direct solar radiation.
■ In automatic mode, control the spot via timer and / or twilight switch.
Maintenance, disposal
Care
■ Clean the spot with a damp cloth every now and then.
■ The luminaries are made of stainless V4A steel. However, depending on the environmental
conditions and the surfacing material, the metal parts may present the so-called flash rust, but
this does not constitute a defect. Flash rust can be removed easily with appropriate stainless
steel cleaners. Flash rust is particularly likely when the housing comes into contact with ferrous
particles (e.g. iron and grinding dust, ferrous plant fertilizers or the like).
5-pin plug
clarios-mini RGB
red S-PWM
green S-PWM
12 V +
blue S-PWM
ground (-)
23