DOTECH DPX100-150-R4-KGF 사용자 설명서

{카테고리_이름} DOTECH DPX100-150-R4-KGF에 대한 사용자 설명서을 온라인으로 검색하거나 PDF를 다운로드하세요. DOTECH DPX100-150-R4-KGF 4 페이지. Digital pressure switch

페이지 인쇄

Digital Pressure Switch

DPX100

User Manual

DOTECH INC.

6F, JOONGANG-ILBO B/D, 30, Dongsan-ro, Danwon-gu, Ansan-si, Gyeonggi-do,

KOREA

TEL: +82-31-495-3767 FAX: +82-31-495-3917

www.dotech21.com

OVERVIEW

: SPECIFICATIONS(STANDARD MODEL)

Description

100 – 240 Vac, 50/60 Hz

Power

Power Consumption

MAX 10 VA

Output

3P Relay Outputs / 250Vac, 30Vdc, 5 A

Measurement

DPX100-115 : -0.10 ~ 1.50 MPa

Range

DPX100-150 : -0.10 ~ 5.00 MPa

Accuracy

±1.0 %FS

Overpressure

150 %FS

Stability

±0.5 %FS/year

Pressure

Shock

20 g sinusoidal, 11 msec

Sensors

Vibration

x-y-z directions of 5 -2000Hz / 10g

Working Temp.

-40 ~ 120 °C

Connection

7/16UNF" / MALE

Pressure Type

Gauge

Dimensions

159(W)mm X 128(H)mm X 58(D)mm

Operation

Temperature -10~50 °C / Humidity 90%RH or less

Storage

Temperature -20~60 °C / Humidity 90%RH or less

Supplied Contents

※ This item is provided for securing the bracket tightening all bolts please.

CAUTIONS

1. This product may cause an electric shock in handling. Please do not attempt to open it with power turned on.

2. This product should be installed in a place fixed secured by a rack or panel.

3.This product can be used under the following environmental condition.

① Indoor ②Pollution Degree 2 ③At an altitude of 2000m or below

4. Power input must be within the designated ranges.

5. To turn on or turn off power supply for this product, please the circuit breaker or switch of a standard product of IEC

60947-1 or IEC 60947-3 product and install it within a close distance allowing convenient operation by user.

6. Please be understood that if this product is dismantled or modified discretionary, after sales service will not

be able to be provided.

7. An output wire to be used for this product should be inflammable grade FV1 (V-1 grade or above), the thickness

of the wire should be AWG No. 20 or above(0.50mm

8. In order to prevent it from an inductive noise, please maintain the high-voltage wire and power wire separated.

9. Please avoid installing the product in a place where a strong magnetism, noise, severe vibration and impact exist.

10. When extending the sensor wire, use a shield wire and do not extend it unnecessary long.

11. The sensor wire and signal wire should be away from the power and load wires using conduits separately installed.

12. Please avoid using the product near a device generating strong high frequency noise (high-frequency welding machine,

high-frequency sewing machine, high-frequency radiotelegraph, high capacity SCR controller)

13. Product's damages other than those decribed in the guarantee conditions provided by the manufacturer shall not be

respoinsible by us.

14. If this unit is used to control machineries (Medical equipment, vehicle, train, airplane, combustion apparatus,

entertainment, processing and transportation equipment, elevator and various safety device etc.) enabling to effect

on human or property, it is required to install fail-safe device.

※ The Aforementioned precautions must be observed, and if you fail to do so, it may cause a product's breakdown

※ The specifications, dimensions, and etc. are subject to change for enhancement without a prior notice.

FEATURES

※

DPX100 is a digital pressure switch with functions of several pressure switch and

gauges. It measures the low pressure of suction or the high pressure of discharge

of compressor and controls the pressure within predetermined ranges.

: SELECTION GUIDE

Model

Description

DPX100-115 / Low Pressure Sensor = -0.10 ~ 1.50 MPa

Digital Pressure Switch Standard(Pressure Unit:: MPa )

DPX100-115-00-MPA